Saturn L-Series
VW Passat
Ford Bronco II

How do you remove a passenger seat from a Saturn?

515253

Top Answer
User Avatar
Wiki User
2009-03-15 21:35:20
2009-03-15 21:35:20

To remove the passenger seat in a Saturn SL2 2002 you need an E10 inverted torque socket. Saturn mechanic tells me this is a standard tool, but is not widely available because they have not been used for very long. I found a set of inverted torque sockets, which included the E10, at a tool crib store in North Hollywood, JM Tools on Sherman Way at 818 764-8973, for under $20.00 The socket works fine, the seat lifts right out after you unbolt the four bolts holding the seat in place. Now, if I can just figure out how to detach the mounting brackets from the seat adjusting rails, I can install my aftermarket racing seats. Darn things are riveted on, and I'm really not happy drilling them off. Oh well. OR you can remove the covers located at the four base feet and use a good old metric socket done it many times don't need any tools other than the ones you have.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

passenger side back seat, behind the panel by the door. may have to remove floor panel and/or seat.

User Avatar

remove passenger seat in 2003 cadillac cts

User Avatar

The seat rails are bolted to the floor of the passenger compartment. Remove the bolts and any connected wiring and the seat should be easily removed.

User Avatar

You have to remove the Allen bolt on the rear of the passenger seat, then remove the two Allen bolts exposed when you removed the passenger seat. The driver seat should slide back and off now.

User Avatar

Remove front passenger seat on Lexus es300?

User Avatar

how to remove front passenger seat of 1996 Honda Civic EX 2 door coupe

User Avatar

You have to remove the 28 mm bolts at the rear of the passenger seat on either side of the tail light. Now slide the passenger seat back to release a clip holding the front edge of the passenger seat. Then remove the 12 mm bolts holding the seat to the frame.

User Avatar

the folding tray OS bolted to the passenger seat. the passenger seat must be removed in order to unbolt the tray from the seat.Do not remove the passenger seat. remove the cover that attached to metal bracket of p. seat. it's mounted with two plastic screws. use flat screw driver to remove. then you will see 3 bolts on the bracket attached to p. seat. remove bolts and pull away.

User Avatar

Front bolts on the side and then you have to remove the passenger seat first then the bolt for the front seat will be visible

User Avatar

To remove the seat on a road king classic you will need to take a screw driver and remove all the bolts then remove the passenger side seat.

User Avatar

4 airbags in 2004 Saturn L-300; front driver and front passenger; roof mount side impact driver and directly behind back seat passenger and roof mount side impact passenger and directly behind back seat passenger

User Avatar

A front passenger seat on a 2005 Honda Civic is held on by four bolts. Pull the seat back to loosen the front two. Pull the seat forward to reach the two rear bolts. Remove the seat.

User Avatar

remove the passenger pad first, when removed it uncovers screws on the rear of the drivers seat. Remove these and it comes off.

User Avatar

Should be a bolt in each corner of the seat

User Avatar

remove the 4 nuts, one on each leg of the seat and unplug any wiring harnesses under the seat and pull out the seat.

User Avatar

behind the passenger seat you will see a nut. unscrew it, left and remove the passenger seat. then you will see another bracket with 2 Allen screws. unscre those and you can lift off the main seat

User Avatar

Hi sit in the back behind the passenger seat and remove the headrest. Tilt the seat as far as possible foward, on the slides of the seat in the bottom left and right is levers that needs to be pressed and that will release the seat and swiwel foward.

User Avatar

It is under the rear passenger seat. You have to remove the seat to gain access. If you bend low and look under the front of the seat you will see the mechanism to remove the seat.

User Avatar

remove bolt on the back of passenger seat, pull that back and out. Then driver seat just pulls back and out as well.

User Avatar

Remove rear screw, pull seat rearward until front tab disengages from under the tank, remove seat by pulling seat forward and sliding the strap over the passenger seat (requires some tugging at the strap). To replace slide the strap over the passenger seat pushing the seat rearward until the tab slips under the tank.

User Avatar

It is under the passenger seat, you will have to remove the passenger seat then the rug will have to be pulled back to access the module.

User Avatar

Remove the Allen head bolt that fastens the passenger seat . Then lift this seat upward and pull it back to remove it. Next, find the two bolts that fasten the rider's seat at the rear. Remove them and lift the seat up and pull it back a bit.

User Avatar

Four bolts under seat from frame into flooring, remove and lift out seat. Unplug any electrical connections as needed before removing seat from car.

User Avatar

Remove Snookie from the passenger seat.

User Avatar

Using the correct size Allen wrench, remove the passenger handles on each side of the bike. Then, lift the rear of the seat up and pull rearwards after it clears the passenger backrest.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.