Starters and Ignition Systems
Mercury Tracer
Ford F-250
DIY Projects

How do you remove an ignition lock on a 1992 Tracer wagon?

565758

Top Answer
User Avatar
Wiki User
2007-05-19 20:28:13
2007-05-19 20:28:13

On my '91, it went like this: Borrow a steering wheel puller. Remove the horn pad, (four screws on the backside of the steering wheel. Remove the wheel. The rest is a cake-walk and simply a matter of Removal and reinstallation. The ignition switch has a tab on the side opposite of the key that is prone to breaking. It's quite doable without spending a hundred dollars an hour if you have a decent socket set and a steering wheel puller in hand.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Type your answer here... How do you remove ignition switch from 1992 ford explorer?

User Avatar

No, they are a different part number and are different steering columns. Stick with the escort/tracer switch. No, they are a different part number and are different steering columns. Stick with the escort/tracer switch.

User Avatar

R-12 was outlawed in 1992. Why don't you use R-134A. Put in into the low-pressure port.

User Avatar

Begin by removing the retaining ring at the top of your 1992 Chevy ignition switch. The ignition switch will slide out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install the new ignition switch.

User Avatar

It would need to be drilled. Best to just call a locksmith.

User Avatar

you need to have the ignition barrel in the on position otherwise you cant to it.

User Avatar

The 1992 Plymouth Cold ignition switch is held in place by a retaining ring. Remove the retaining ring at the top of the ignition switch. Pull the ignition switch out. Remove the wiring harness from the ignition switch. Reverse the process to install the new ignition switch.

User Avatar

For a 1992 Mercury Tracer : firewall 1-----2-----3-----4 front of vehicle > driver

User Avatar

You need to turn the ignition to the on or start position, and then push the retaining pin to remove the cylinder. If you can not turn it, then you can either drill it out, or call a locksmith to come asist you.

User Avatar

First remove the steering wheel, remove the torx screws and remove the house, remove the signal switch and the wiper switch, remove the torx screws and?รฆremove the ignition switch. Put in the new switch and replace everything in reverse.?รฆ

User Avatar

I removed my ignition switch with a screwdriver and a power drill. I warn you it damaged the whole system though. I have to start it with a screwdriver now.

User Avatar

You can't get a locked ignition out of a 1992 Lincoln Town Car. Turn the ignition on to take it out

User Avatar

With the key turned to on find something like a thin Allen wrench and push it in to the hole under the ignition and it should pull right out

User Avatar

The complete instructions are in Haynes manual #38025 (1420). You actually have to remove the steering wheel first. Amazon should have this cheap.

User Avatar

how do you replace ignition switch on a 1992 Chevy cavalier 2.2 4 cylinder

User Avatar

Where is the ignition control module located in my 1992 Crown Victoria

User Avatar

Why won't the keys in the ignition turn on a 1992 grand marquis?

User Avatar

How do you replace the ignition swith opn a 1992 Pontiac Bonneville se

User Avatar

Every Tracer I know of has spark-plugs unless you have a diesel engine from overseas. Please check with a knowledgeable mechanic.

User Avatar

The 1992 Chevrolet Corsica ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.

User Avatar

Take the knobs off and the nuts under them. Then take off any bolts in the rear holding it and remove the wireing.

User Avatar

where is camshalf pulley ignition timing location for 1992 Toyota corolla?

User Avatar

The 1992 Dodge Ram 250 ignition module is located on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.

User Avatar

1992 Saturns had electronic ignition and did not have distributors.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.