answersLogoWhite

0


Best Answer

take a 3/8" ratchet, insert it into the tension pulley (there will be a square slot on the outside), turn it until the belt loosens up enogh to pull the belt off the alternator pulley. unplug the wire that goes into the back of the alternator, and remove the bolts of the bracket, reverse to install. Thanks to the person above who answered this for me. This has been done. I started my car after puting the new one in and the light came on. It is a code 41 (field generator not switching properly). What exactly does this mean and what possibilities could be causing this? I did have the battery cables off while I was installing the new alternator. I am afraid of letting the car run for the battery to charge back up not knowing what else may be going on with the code 41.

User Avatar

Wiki User

โˆ™ 2005-09-16 13:16:02
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove and install an alternator on a 1997 Plymouth Neon Espresso with step by step instructions?
Write your answer...
Submit
Related questions

How do you replace the alternator on a 1992 Plymouth Grand Voyager?

Remove the wiring harness from your 1992 Plymouth Grand Voyager alternator. Remove the alternator belt. Remove the alternator retaining bolts. Reverse the process to install your new alternator.


How do you install an alternator in a 1971 Plymouth duster with a slant six?

first unhook the battery cables and then take the alternator belt loose and then take the 3 bolts out that hold the alternator on and take the wiring harness out of the alternator and the red battery cable off and it's out.


How do you replace the alternator on a 1986 Nissan truck?

There are two bolts on the bottom of the alternator that you can't see but you can feel them, these are the pivot bolts, remove them. Then remove the adjustment bolt on top of the alternator. Remove wiring from back of alternator. Reverse instructions for install.


How do you install alternator on 2000 Ford diesel truck?

how do you install alternator on 2000 Ford diesel truck


How do you install a r4736 relay in a 1999 Plymouth Voyager?

how i install a R4736 relay in a 199 Plymouth voyager


Where can you find a guide to install an alternator on a Chevy Silverado?

buy a haynes or a chiltons repair manual for your truck both provide detailed repair instructions


Install 84 t bird alternator?

Loosen the tensioner pulley. The alternator belt will become loose. Take off the belt. Remove the wiring harness from the alternator. Remove the retaining bolts from the alternator. Remove the alternator. Reverse the process to install the new alternator.


How do you install a alternator on a ford 460?

alternator locked up after installing it what did i do wrong?


How do you install an alternator on a 1993 mercury topaz?

I also need to know how to install a alternator in a Mercury Topaz, but my car is a 1991. PLEASE HELP...


How do you install an alternator belt on 1986 GMC s15 pickup truck?

How do you install an alternator belt on a 1986 GMC s15 pickup truck


How do you replace an alternator on a 1991 buick regal?

Disconnect the 1991 Regal battery. Remove the alternator belt and wiring. Unbolt the alternator and install the new one. Reconnect the wires, install the belt, then reconnect the battery.


How do you change an alternator in your 1995 gs300 Lexus?

2JZ-GE Engine # Disconnect the negative battery cable. Wait at least 90 seconds before performing any other work. # Remove the engine undercover. # Turn the drive belt tensioner clockwise and remove the drive belt from the engine. # Disconnect the generator electrical connector. # Remove the rubber cap and nut and then disconnect the alternator wire. # Disconnect the alternator wire clamp from the wire clip on the alternator. # Disconnect the A/T coolant hoses and bracket from the alternator by removing the bolt and pipe clamp. # Remove the alternator bolt, nut, pipe bracket and then remove the alternator from the engine. To install: # Install the alternator and pipe bracket. Torque the bolt and nut to 27 ft. lbs. (37 Nm). # Install the A/T oil cooler pipes to the alternator and install the bolt and pipe clamp. # Connect the alternator wire clamp to the wire clip on the alternator. # Connect the electrical wire to the alternator and install the nut. # Install the alternator electrical connector. # Install the drive belt. # Install the lower engine cover. # Connect the negative battery cable. # Start the engine and check the charging system for proper operation


How do you change alternator of a 1994 Lexus GS300?

2JZ-GE Engine # Disconnect the negative battery cable. Wait at least 90 seconds before performing any other work. # Remove the engine undercover. # Turn the drive belt tensioner clockwise and remove the drive belt from the engine. # Disconnect the generator electrical connector. # Remove the rubber cap and nut and then disconnect the alternator wire. # Disconnect the alternator wire clamp from the wire clip on the alternator. # Disconnect the A/T coolant hoses and bracket from the alternator by removing the bolt and pipe clamp. # Remove the alternator bolt, nut, pipe bracket and then remove the alternator from the engine. To install: # Install the alternator and pipe bracket. Torque the bolt and nut to 27 ft. lbs. (37 Nm). # Install the A/T oil cooler pipes to the alternator and install the bolt and pipe clamp. # Connect the alternator wire clamp to the wire clip on the alternator. # Connect the electrical wire to the alternator and install the nut. # Install the alternator electrical connector. # Install the drive belt. # Install the lower engine cover. # Connect the negative battery cable. # Start the engine and check the charging system for proper operation


What do you need to do when replacing a alternator with a high output alternator?

Noting, just install it and hook it up.


How do you replace an alternator or vauxhall vectra?

You will need to remove the alternator belt. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.


How do you replace the alternator in a 1967 mustang?

Remove the belt from your 1967 Ford Mustang alternator. Disconnect the alternator wiring. Remove the alternator retaining bolts. Reverse the process to install the new alternator.


How do you replace an alternator on 2003 mustang gt?

Remove the alternator belt from your 2003 Ford Mustang alternator. Remove the wiring harness from the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.


Where can one get instructions on how to setup and install PVP?

There are many websites and resources that offer instructions on how to setup and install PVP software. The best website to get instructions on installation is the PVP website.


How do you change the alternator belt on a Volvo 240 dl?

Begin by removing the alternator tensioner bolt. Slide the alternator to the left. Remove the alternator belt. Reverse the process to install the new alternator belt.


How do you replace the alternator on a 1990 Subaru Loyale?

Remove the wiring harness from your 1990 Subaru alternator. Remove the alternator belt. Remove the alternator retaining bolts. Reverse the process to install your new alternator.


How do you replace alternator on Volvo wagon?

Remove the alternator wiring harness. Loosen the tensioner pulley. Remove the alternator belt. Remove the alternator retaining bolts. Reverse the process to install the new alternator.


Change an alternator in a 97 Chevy Blazer?

Remove the alternator belt by loosening the tensioner pulley. Remove the wiring from the alternator. Remove the retaining bolts to the alternator. Reverse the process to install the new alternator.


How to replace an alternator on a 2000 Monte Carlo?

Remove the alternator belt from your 2000 Chevrolet Monte Carlo alternator. Remove the wiring harness from the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.


How do change an alternator on 1996 Ford Ranger?

Remove the alternator belt from your 1996 Ford Ranger alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.


How do you change the alternator on a Mercury Tracer?

Remove the belt from your Mercury alternator. Remove the wiring harness from the alternator. Remove the retaining bolts. Reverse the process to install your new alternator.

Study guides

๐Ÿ““
Create a Study Guide