answersLogoWhite

0


Best Answer

This is a quick answer. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wore plug into the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery. If you have ever removed or replaced a starter this is cake, that is the hardest part of the job. Rich

User Avatar

Wiki User

โˆ™ 2006-04-19 01:46:41
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove and replace 2000 intrigue crankshaft sensor?
Write your answer...
Submit
Related questions

Where is the crankshaft sensor on 99 Intrigue 3.5L?

Someone believes you should, "Take Your coolant tank off and the sensor is located under it. It's fairlly simple to replace once you find it."; You will find a sensor there but not the crankshaft sensor. On a 99 Intrigue with a 3.5L, the crankshaft position sensor is in the engine block just above and behind the starter. get under the car, remove the starter and you should find what you are looking for.


Crankshaft position sensor 2002 Oldsmobile Intrigue 3.5L?

depending on the year, I have a 2002 intrigue, it is located just above the starter, it needs to be removed to remove the crankshaft sensor, 15mm for starter and 10mm for sensor 1 bolt , not to difficult.


How do you replace the crankshaft positioning sensor on a 1989 ford sho Taurus?

To replace the crankshaft positioning sensor on a 1989 Ford Sho Taurus, go near the water pump at the front of the car and remove components that block access to the sensor. Remove the two bolts holding the sensor in place remove the wire that sends data. Finally, replace the crankshaft positioning sensor.


How do you replace a crankshaft position sensor on a 1999 Oldsmobile Intrigue 3.5L?

It is located above the starter. you must remove the starter for access. Make sure you disconnect the battery first.


How do you replace a crankshaft sensor on a 1997 Landrover Discovery?

Begin by removing the rear engine cover from your 1997 Land Rover Discovery. Remove the crankshaft sensor wiring harness. Remove the crankshaft sensor retaining bolts. Reverse the process to install your new crankshaft sensor.


Where is the crankshaft position sensor located on a 1998 Mitsubishi Eclipse?

Crank position sensor is located next to the crankshaft. In order to replace it you might have to remove the timing belt. In the most models you just can remove remove the timing belt cover and replace the sensor.


Where is the crankshaft sensor on a 1998 INTRIGUE?

Right next to and somewhat behind the crankshaft pulley


How do you replace crankshaft sensor on 2001 s10 blazer?

Locate the crank sensor behind the vibration damper (crankshaft pulley). Unplug the wire harness connected to it. Remove the small bolt holding the sensor in place. Remove the sensor.


Do you have to get under the car to change the crankshaft on an 04 pt cruiser?

You have to remove and disassemble the engine to replace the crankshaft.If you mean the crankshaft position sensor, then yes. You access it from underneath. It is just above the oil pan on the back of the block.You have to remove and disassemble the engine to replace the crankshaft.If you mean the crankshaft position sensor, then yes. You access it from underneath. It is just above the oil pan on the back of the block.


How do you remove a Crankshaft Position Sensor?

how to remove crankshaft position sensor from 91 Buick Regal


How do replace crankshaft sensor on 1997 le sabre?

Remove belt, remove crankshaft bolt with air impact tool, remove balancer pulley with a balancer puller. Then you will be able to get to it.


How do you replace crankshaft sensor?

how to replace crankshaft sensor on Corsa 1-2 2002 .Which parts require removing to replace unit


How do you replace the crank shaft sensor on a LDV Maxus?

The crankshaft sensor, on an LDV Maxus can be changed by removing the rear engine cover. The sensor is attached to the crankshaft with 3 bolts. Remove the bolts and install the new sensor.


Show you a diagram of where the crankshaft sensor is located on a 2000 Oldsmobile Intrigue?

Is this a 3.5L Intrigue V6 engine? If so, it should be behind the left exhaust manifold. You will need to remove the starter to gain access.


What does error code P0385 on a 2002 intrigue mean?

crankshaft sensor b circuit


Where is the crankshaft position sensor located on a 1999 Oldsmobile Intrigue and how is it replaced?

The crankshaft sensor is in the front of the engine.Above the starter.You will have to drop the starter.2 15mm bolts.Look up and there it will be.


How do you replace 2001 olds intrigue crankshaft position sensor?

You have to drop the starter on the front bottom driver side of the engine... next to the transmission. The crank sensor is about in the middle of the block. One bolt holds it in.


How do you replace the crankshaft position sensor on a Chrysler PT Cruiser?

The crankshaft position sensor on the PT Cruiser is on the side of the engine above the oil filter. The sensor is removed with two screws. Unplug the wiring, remove the bolts, then install the new sensor.


How do you replace crankshaft position sensor on a 1988 olds 98?

To replace the crank sensor you have to remove the harmonic balance taking special attention not to damage the pulley or the cam shaft. Remove the two 10mm retaining screws


Where is the camshaft position sensor located on a 1999 Oldsmobile Intrigue and how do you replace it?

where is the camshaft position sensor located on a 1999 Oldsmobile intrigue


On a 2000 Olds Intrigue where is the crankshaft position sensor located?

I have Olds Intrigue 2000 3.5L. Needed to replace faulty crankshaft sensor.3.5L engine has two of them. If engine is hard to start cold or hot and engine light is OK.Very common problem for this engine in Aurora 3.5 and Intrigue 3.5 is crankshaft position sensor. Which is located above and behind starter. Starter must be removed first.------------------------------------------------------------------------------------------------------------AnswerLower right hand side of the engine just above the oil pan. Theres a single bolt that holds it in.


What does crankshaft sensor look like on 1999 Oldsmobile intrigue?

looks like a normal sensor, I have a 2002 intrigue, it is located just above the starter, you have to take out the starter in order to take it out.


What happens if the crankshaft position sensor goes out in a 2001 Oldsmobile intrigue?

The engine won't start.


How do you install a crankshaft position sensor on a 2000 Oldsmobile Intrigue?

This is a quick answer. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wore plug into the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery. If you have ever removed or replaced a starter this is cake, that is the hardest part of the job. Rich


How do you replace crankshaft sensor on 1998 eclipse?

You nee to remove the crankshaft belt pulley, after that remove the lower timing belt cover. When you do that, you will gain access to the sensor and you should be able to replace it. After removing the lower timing belt cover you may need to turn the crankshaft so that the timing blade is not in the slot of the crankshaft timing sensor. On mine for some reason it doesn't like to come off with the blade on there at all, but mine got bent and so I replaced it with aftermarket timing sensor blade.