Clutches and Flywheels
Nissan 240SX

How do you remove and replace a clutch fan on a 93 240sx?

101102103

Top Answer
User Avatar
Wiki User
2006-02-05 01:34:12
2006-02-05 01:34:12

the clutch fan is easy to remove and replace. you will see it on the upper most pully(water pump). just four 10mm nuts to take off. however the pully likes to spin so i use a screwdriver to hold it still or you could tighten the belt so it wont spin, just remember to loosen the belt back to where it is supposed to be once you are done.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the fan belt, by loosening the tensioner pulley. Remove the fan clutch with the retaining bolts. Reverse the process to install the new fan clutch.

User Avatar

How to remove fan clutch on 2003 ford explorer

User Avatar

Usually there are 4 nuts holding the clutch and fan on to the water pump shaft. Just pull the nuts, remove the fan clutch and replace it.

User Avatar

how do you remove a fan clutch from a 2004 volkswagon passat 2.8 motor

User Avatar

Remove the fan itself then remove the clutch from the fan

User Avatar

HI, The first question I need to know is, have you removed the fan yet? And why do you want to remove the clutch? Are you trying to replace the fan/clutch assy? If you have not removed the fan/clutch then here's how to get that out. First drain the cooling system so the coolant is below the upper radiator hose. Take the upper hose off of the radiator. remove all of the fan shroud retaining fasteners. Loosen all of the fan/clutch mounting fasteners. remove the water pump drive belt. Remove the fan/clutch mounting fasteners, then lift the fan/clutch and fan shroud out together. Then remove the clutch however you can. Reverse what you did to replace everything and replace the coolant. This could be a good time to replace all your coolant if it hasn't been done for as while. Good luck and if you need more help, we hope you'll clarify your question. Steve H.

User Avatar

If Possible Get rid of your Clutch Fan and go Electric! But to answer the question, remove serpentine belt and use a strap wrench to stop clutch from spinning when you try to remove fan clutch nut from water pump!

User Avatar

You will need to remove the radiator shroud to get access then release the belt tensioner and remove the belt(s) that restrict access to the fan clutch. Finally, remove the bolts that hold the fan clutch in place. Reverse the process. Done. I hope this helps you. Mark

User Avatar

you have to have fan clutch wrenches

User Avatar

Remove the shroud and the fan. loosen the clutch bolts .... not always easy. We have more detailed instructions at our enthusiasts website. www.trailvoy.com

User Avatar

First you have to remove the fan shroud which is bolted to the radiator and front cross bracket with 10mm bolts. There should be 4 10mm bolts that hold the fan and clutch to the water pump. What you generally have to do is find a way to hold the clutch fan in place, I have used a large flat tip screwdriver in the past. Then you have to loosen the 4 bolts and remove the clutch and fan as a single unit. Once out of the vehicle you should be able to remove the fan from the clutch unit and only replace the clutch unit itself. Hope that helps a little Michael

User Avatar

To remove the fan clutch on a Chevy Tahoe, the upper fan shroud must first be removed. Once removed, a tool is needed to hold the clutch in place to allow for the fan to be removed. The nuts must be unscrewed on the fan in a counterclockwise rotation. Remove the nuts on all side and the fan clutch will remove.

User Avatar

how to remove the clutch fan on the 530i bmw

User Avatar

You need to remove the upper hose and then the fan shroud on the upper half. The fan clutch is then held on with 4 bolts. Remove these and the fan will slide out from the engine. You might need to loosen the belt so you can turn the fan and get to all 4 bolts. With the unit removed you can then remove and replace the fan on the clutch assy. Reinstall in the reverse order.

User Avatar

fan clutch screws off water pump fan pump has left hand thread so to remove you need to turn clockwise

User Avatar

What is the problem? Do you want to replace fan or fan clutch?

User Avatar

You need to rent or buy a fan clutch removal tool kit. you need to remove the fan and clutch as one before you can separate the fan from the clutch.

User Avatar

the fan clutch is built into the water pump,it cant be separated,you have to replace the water pump.

User Avatar

Yes it takes a 36mm wrench and a holder for the pulley to remove the fan clutch,

User Avatar

remove fan belt fan clutch scres off the water pump this is usually a left hand thread so in this case it will be righty loosy lefty tighty remove fan blades before you remove fan clutch

User Avatar

Consult www.trailvoy.com for a detailed "how to" on this very common problem with early model years. Basically remove fan shroud, fan, then the clutch. A special tool is available for rent or borrow (most auto parts stores) to help remove the clutch. be sur eto get the newest part number available. #25790869

User Avatar

how do you remove the fan clutch on a 1992 318i 1.8 liter?

User Avatar

The wench will be used to remove the clutch fan nut. Remove the nuts holding the fan then remove the fan blade.

User Avatar

to remove a clutch fan on a ford, you need special tools . also fan thread is left hand thread ,so you unscrew it clockwise


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.