Does anyone know how to take off a radiator fan clutch from a 1998 Dodge Dakota 3.9 V6
Remove the water from the radiator. Remove the radiator hoses. Remove the stabilizing arm from the top of the radiator. Remove the radiator retaining bolts. Reverse the process to install the new radiator.
Drain the water from the radiator. Remove the radiator hoses. Remove the radiator stabilizing arm. Remove the radiator retaining bolts. Reverse the process to install the new radiator.
Remove upper radiator support remove bolts that retain the A/C condenser remove hoses and transmission cooler lines remove retaining bolts then remove fan module and lift out radiator
RadiatorRemoval & InstallationAll gasoline-engine equipped trucks use a cross-flow radiator. In this type, the coolant flows horizontally from a radiator inlet tank to a radiator outlet tank.Remove the retaining clips for the radiator support brace trim cover and remove the trim panel from the vehicle.Remove the fan shroud-to-radiator retaining bolts.Place the special fan removal tools over the water pump pulley bolts and onto the fan clutch hub and loosen the fan clutch assembly.Remove the fan clutch from the water pump and remove the fan clutch and the shroud assembly from the vehicle.Slide the hose clamp back and remove the upper and lower hoses from the radiator.Remove the recovery tank hose from the radiator.Using a back-up wrench to support the radiator fitting, loosen the transmission cooler lines from the radiator and plug the lines to prevent contamination from entering the transmission.The radiator is retained by two upper support mounts.Remove the radiator upper support mounts bolts and remove the support mount brackets from the radiator.Remove the radiator by lifting it straight out of the engine compartmentThe installation is the reverse of the removal.
how much cost to replace radiator on 1998 volvo v70
remove the old one and install a new one.
Disconnect the negative cable from the battery. Disconnect the clutch mechanism. Place the car on a jack and remove the engine mounts. Remove the clutch disk along with the other parts. Replace it with a new one.
located at the end of the upper radiator hose. remove two bolts, replace with new parts remember to replace the gasket.
You will need to remove Transmission, And you will see it in the bellhouseing. 4 bolts hold it in place.
Locate the radiator. Disconnect the coolant hoses on the radiator. Unfasten the drain plug. Remove the mounting bolts on the radiator and slide it down to remove it.
Remove the plug at the bottom or the rear of the radiator or remove the lower radiator hose
Drain the radiator into a suitable container. Remove the upper radiator hose at the engine. Remove the 2 bolts holding the thermostat housing and remove the thermostat. Clean both surfaces and install the thermostat and gasket. Install the housing and the upper radiator hose. Top off the radiator.
Remove the lower radiator hose.
1. Drain the cooling system. 2. Remove the air cleaner assembly. 3. Remove the plastic rivet retainers and the air deflector from the vehicle. 4. Disconnect the upper radiator hose from the radiator. 5. Disconnect the overflow hose from the radiator.Remove the fan and fan clutch from the water pump pulley. 6. Remove the bolts and lift the fan shroud, and fan and fan clutch from the vehicle. 7. Raise the vehicle. 8. Remove the underbody splash shield, if so equipped. 9. Compress the clamps and slide away from the radiator. Twist the transmission oil cooler hoses and remove from the radiator. 10. Disconnect the lower radiator hose from the radiator. 11. Lower the vehicle. 12. Remove the bolts retaining the support brackets to the radiator support. Lift the radiator support brackets upwards and away from the radiator. 13. Remove the radiator from the vehicle.
Remove first the radiator mount and hood latch mechanism. Drain cooling system by placing a pan under radiator and allowing it to drip until empty. Remove radiator caps, replace radiator and return radiator mount and hood latch mechanism refill your cooling system with a premium grade coolant.
Drain the cooling system (lower corner on the passenger side of the radiator should be where the drain plug is), remove the upper and lower radiator hose and heater hoses (you simply unclamp and pull them), remove the brackets holding the radiator in (located at the sides and bottom of the radiator), pull out the radiator. Installation is the opposite of removal.
usually at the bottom or rear of the radiator - or remove the lower radiator hose
How hard is it to remove and is there a digram procedure available on-line to remove it.
You would remove it from underneath. There is a cross member which holds the bottom of the radiator and you remove this, after unhooking all the lines (trans coolant and engine coolant) and draining the radiator.
on the bottom . hard to see. if you break it you must replace the radiator
To install and remove the thermostat on a 1998 Suzuki Esteem, drain the radiator. Remove the upper hose assembly and locate the thermostat. Remove the bolt holding it in and put the new one in place before refilling the radiator.
follow the top radiator hose to the engine remove three 10 mil bolts replace o ring