Auto Parts and Repairs
Electric Windows
Oldsmobile Intrigue
Mitsubishi 3000 GT

How do you remove and replace the window regulator in a 1981 Chevy pickup?

293031

Top Answer
User Avatar
Wiki User
2004-12-30 05:19:00
2004-12-30 05:19:00

The question you ask is too involved for a proper answer. You may want to go to a car parts store, or book store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

First you need to remove the door panel.Then remove the door handle bracket.Peel back the moisture shield.Tape the window into place,then unbolt the window from the regulator.Remove the window regulator from the access hole in the door.

User Avatar

How to remove the window motor from the regulator

User Avatar

You will have to replace the complete window regulator assembly.

User Avatar

To replace a rear window regulator on 2005 CTS Cadillac remove the side protection panel of the car door then adjust the regulator.

User Avatar

Remove the window regulator assembly from the door.Remove the motor from the regulator by drilling out the attaching rivets with a 3/16 in. drill bit.Connect the window motor to the regulator with 3/16 in. rivets.Install the window regulator assembly.

User Avatar

First remove the door panel.Then remove the moisture barrier.Next remove the window motor from the window regulator.

User Avatar

remove your door panel there will be three screws holding it on. then you have to remove the screws holding your window to the regulator. then unbolt regulator and motor from door. Undo wiring going to motor.

User Avatar

To install a new window regulator on a MGRZ driver's door, remove the door panel and the wiring attached to the power window mechanism. Remove stereo speaker from the inside door and the window glass. Remove the old window regulator and replace with new.

User Avatar

The panel where the regulator is detachable. You will be able to remove it very easily. When you remove the panel you will see the way how the regulator can be replaced.

User Avatar

remove back seat, remove screws bottom and top of panel, remove panel. remove 3 bolts and motor arm, window and regulator will pull out.

User Avatar

It is best to replace entire regulator as one unit. Remove door panel. Remove bottom nut of regulator, and remove two top nuts of regulator. Loosen two bolts on bracket holding window. Support window, and carefully remove regulator as one unit.

User Avatar

Remove the door panel. Remove the bolt that fastens the regulator to the window. Remove the 3 bolts that hold the regulator assembly to the door. Squeeze the entire assembly through the largest hole and replace with a new assembly in reverse order.

User Avatar

Take the door panel off,you will need to remove 3 bolts for the window motor and then 3bolts(maybe4) that hold the regulator to the window

User Avatar

HOW DO I REPLACE WINDOW REGULATOR MOTOR ON PASSENGER SIDE WINDOW

User Avatar

To remove the drivers side window and regulator, you will need to remove the door panel from the door. Then you can unbolt the regulator and window to remove them.

User Avatar

First, lower window approximately half way. This allows you access to the bolts that attach window to the regulator. Remove door panel. Using a 10mm wrench, remove the two bolts that hold window to the regulator. Then there are two upper and two lower bolts holding the regulator to the door. Then you remove the three bolts for the window motor which is toward the front of the door. You have to also disconnect the plug for the windo motor to remove the entire window regulator and motr that are all one unit. Replace the unit in the reverse way.

User Avatar

Remove the door trim panel.Then clip the window regulator cables. Push window up and tape it in place until you can replace the regulator

User Avatar

I found having a repair manual specifically for your make/model/year a great start. I'm in the same boat and this is what I have found out and will be doing next weekend. First, I had the a screw placed in the regulator to keep the window up until I am able to replace the window regulator. The regulator comes complete with the motor, so what I will do is remove the current regulator have a friend holding up the window has I am doing this so I wont have to remove the window (to skip a step), then just attach the new regulator in the same place as the original.

User Avatar

The window regulator for the Nissan Primera is riveted to the door beneath the interior paneling. You would need to remove both the interior panel and the old regulator in order to replace it.

User Avatar

You would need to remove the door panel, and tape the window into the up position so that you can remove the regulator from the window. I've included a link to an auto repair video that we have to show you how to fix this on your vehicle.

User Avatar

Driver Side Window Regulator Assembly replace on 2004 pontiac grand prix

User Avatar

Begin by removing the inside door panel. Remove the wiring harness from the electric window regulator. Remove the window regulator retaining screws.

User Avatar

To replace the car window on the driver side you will need to follow the following steps. 1. Disconnect the car battery if the window has automatic controls. 2. Remove the window trim and disconnect the window from manual or automatic controls. 3. Unbolt the regulator that holds the glass and remove the glass. 4. Replace the glass and reattach the regulator, controls and trim.

User Avatar

Disconnect the battery.Remove the door panelRemove the power window motorRemove the regulator spring.Move the window down a bit and remove the two 10MM nuts from the window.Twist the window spring stud counter-clockwise.Now you should be able to remove the window regulator.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.