answersLogoWhite

0


Best Answer
Copy

Loosen the screws on the cap and there is a single screw holding the rotor to the shaft

User Avatar

Wiki User

โˆ™ 2015-07-15 19:31:15
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you remove cap and rotor on 1992 Honda Civic 1.6 engine?
Write your answer...
Submit

Related Questions

How do you remove the rotor to access the ignition coil for the Honda Civic?

a little 8 mill screw on bottom of rotor into dist shaft


How do you remove the front axles on a 1993 Honda Civic?

Begin by removing the tire and wheel from your 1993 Honda Civic. Remove the brake assembly and the brake rotor. Remove the axle retaining bolts. The axle will come off.


How to change the rotors on a 1991 Honda Civic?

To change the brake rotors on a 1991 Honda Civic raise the vehicle. Remove the wheels and brake caliper bracket. Remove the brake pads. Loosen the rotor mounting screws and replace the rotors.


How do you change the distributor rotor button on your 98 Honda civic?

To change the distributor rotor on a1998 Honda Civic unplug the spark plug wires from the cap. Loosen the screws and remove the cap on the unit. Be sure to properly line the new cap on the distributor and install.


1994 Honda Accord ex remove rear rotor?

1994 Honda accord ex remove rear rotor


What is the minimum thickness for a 2001 Honda civic brake rotor?

19mm


What is min thickness brake rotor 2010 Honda civic?

3


How to find out if a 2005 Honda Civic LX has geuinge Honda front brake rotors?

there should be a Honda stamp on the inside center of the rotor


How do you change a CV joint on a 1987 Honda Civic?

Begin by removing the tire and wheel from your 1987 Honda. Remove the brake assembly and the brake rotor. Remove the CV joint retaining bolts. Reverse the process to install your new CV joint.


How do you or what needs to be done to replace a rotor on a 2003 hoda civic a style'text-decoration: none; border-bottom: 3px double;' hrefhttp:wwwserverlogic3comlmrtl3aspsi24khonda civic onmo?

Remove wheel. Remove Brake assy. Remove two screws on rotor. Remove Rotor. Replace Rotor. Tighten Screws. Reinstall Brake assy. Reinstall wheel.


Where is the speed sensor located on a Honda civic 95 ex?

The 1995 Honda Civic speed sensor is located on the front passenger wheel. The speed sensor will be found on the inside of the brake rotor.


What is the firing order from distributor cap to spark plug on Honda civic 1.5 procedure on timing a Honda Civic?

Firing order is 1-3-4-2 Rotor turns clockwise.


Where is the ignition control module on a 1994 Honda civic dx?

Inside the distributor cap under the rotor


What is the best distributor rotor brand for Honda civic LX 2003?

MSD w/ a rev limitor.


How do you remove the front passenger brake rotor on a 92 Honda accord?

Remove wheels Remove caliper mounting bolts Slide caliper off rotor Slide rotor off hub (if "peel off" type)


What is the firing order for a 1993 Honda civic lx?

1-3-4-2 rotor turns clockwise.


Replace front wheel bearing - 1997 Honda Civic?

Remove lug nuts & tire, remove rotor. Then must remove brake caliper - 2 bolts. Then must remove hub bolts behind rotor that holds hub to steering knuckle, 3 bolts. Remove bearing hub assembly and wiring attached to it. Takes experienced mechanic 1/2 hour or so.


How do you remove front rotors on a 2000 Honda Passport?

Remove wheels Remove caliper ( 2 mounting bolts) Slide caliper off rotor Rotor should slide off hub


How do you take off the rotor under the distributor cap on a 1998 Honda civic?

Is there a screw holding it on? Look for a black plastic cover over the coil restricting your access to the base of the rotor. You may need to remove this cover. You might also need to crank the engine to a different position fo access the screw if it has one. If there is no such screw, just pull the thing off.


How do you take the front wheel hub on a 94 civic so that you can change the studs?

The front wheel hub on a 1994 Honda Civic is connected to the upper control arm and lower. Remove those as well as the axle. Also remove the brake caliper, rotor, and pads. The hub will come off and the studs will then be able to be reached.


How do you get the rotor off of a 99 Honda Civic Ex?

well first u gotta get the caliper housing off then just take your impact screwdriver and remove both counter sunk screws and beat off rotor in a star like pattern side to side ect.......


What is minimum brake rotor thickness on a 2000 Honda Accord?

For a 2000 Honda accord, according to the specifications at autozone.com:.905 (In thousandths of an inch)Application:Front rotor.394 (In thousandths of an inch)Application:Rear rotorWith 4 cylinder engine.354 (In thousandths of an inch)Application:Rear rotorWith 6 cylinder engine


Remove front rotors 2004 Honda accord?

Remove the tire and wheel. Remove the brake pads and break hardware. The brake rotor will slide off. You may need to tap the rotor with a hammer.


What is the min thickness front rotor for 1991 Honda Accord?

Front rotor is .905 (In thousandths of an inch)Application:Rear rotorWith 4 cylinder engine.394 (In thousandths of an inch)Application:Rear rotorWith 6 cylinder engine.354 (In thousandths of an inch)


What else besides the distributor cap and rotor could cause starting problems in a 1995 Honda Civic?

Try the main relay. Mine was behind the glovebox on a 1996 civic. Good luck.