The headlight assembly does not need to be removed in order to change a light bulb. Take hold of the light bulb connector. Push the connector in and turn to the left at the same time. The light bulb will come out.
be more specific. what year is it? on my bike the headlight assembly sits in 2 grommets that are part of the bracket and also bolting to the gauge cluster assembly. 1 grommet on the left the other on the right. than, in each top left and right corner of the headlight shoud be Phillips or 7mm metric screws. they bolt into the upper fairing, holding the light flush.
The headlight assembly on a 2000 Acura Integra is held on using bracket bolts. Prop the hood open and locate the headlights. Unbolt the brackets and remove them. Carefully pry the headlight assembly out to not harm the weatherstripping.
first remove the bracket over the top of the light, should take a Phillips head screwdriver. second remove the upper adjustment screw bracket from the radiator frame using a needle nose pliers. Then using a needel nose plires squeeze the retaining clip on the lowere adusting screw while pulling out on the headlight.
I have a 2006 Honda VTX1300R The headlight assembly has two holes for adjusting screws in the bottom at about 4 oclock and 8 oclock. Insert a Phillips screwdriver until it "catches" the screw. Turning it clockwise will raise the light beam on that side. It is not easy. however; this does not always work. I am not a certified motorcycle mechanic. This is what I did after five months of trying everything else. Do it at your own risk. My bike's adjustment came from the dealer so far off, that I had to remove the complete headlight assembly form the bike. Then removed the black bracket from the headlight assembly. Slightly bent the black bracket where the screws go to the bike. I did this by holding each side of the black bracket plate on a press, and carefully and slightly bending the "holes" where the screws hold the black bracket to the base on the bike. Then mounted everything back. Now I can ride my bike at night. Hope this helps.
This is for the passenger side headlight assembly in a 1998 Grand Am SE. Fairly certain they are identical to the GT. The driver's side is has a plastic cover that must be removed first, so the setup underneath may or may not be different... Remove the three 10mm hex bolts from the top of the headlight assembly holding it to the vehicle. The middle bolt has a bracket connecting it to the vehicle by a fourth hex bolt, which you may need to loosen to move the bracket out of the way. Pull the headlight assembly forward until you can access the bulbs. They can be removed from the assembly by a quarter turn, then unclip the faulty bulb and replace.
This is for the passenger side headlight assembly. The driver's side is has a plastic cover that must be removed first, so the setup underneath may or may not be different... Remove the three 10mm hex bolts from the top of the headlight assembly holding it to the vehicle. The middle bolt has a bracket connecting it to the vehicle by a fourth hex bolt, which you may need to loosen to move the bracket out of the way. Pull the headlight assembly forward until you can access the bulbs. They can be removed from the assembly by a quarter turn, then unclip the faulty bulb and replace.
Yes. Just switch the headlight brackets out.(remove the headlight bracket from the CRX headlight/ install the CIVIC headlight bracket on the CRX headlight.
Very easy. Takes about 3 minutes. Raise the hood. Raise the headlight manually by turning the black knob behind headlight. Headlight assembly is on an L shaped bracket. Side toward radiator has 2 bolts. Back side toward fender has 3 nuts. Remove these and disconnect wiring connecter laying on fender. And carefully lift out whole assembly.
It is under headlight on the passenger side and behind the foglight. You either have to access it from the fenderwell or or by removing the headlight (easier method). It is held on a bracket with one bolt.
There are 3 wing nuts holding the headlight bracket. Remove these and unplug wire going to headlight. Remove bracket from van and then the headlight can be removed from bracket.
(1997-2003 models) If you pull back the carpet on the drivers side of the trunk you will see a bracket. The bracket mounts the emergency fuel pump cut off and a fuel pump relay (i believe). Upon removal of the bracket (2 Phillips screws and a 11mm bolt) the Power Antenna assembly is exposed. After unscrewing the mast nut (on the exterior of the car) and removing two 11mm nuts you can unplug and disconnect the Power Antenna assembly. Installation is reverse of removal.
Remove the flasher retaining bolts from the headlight assembly bracket. Remove the wiring harness. Reverse the process to install the new flasher.