Use the type of vacuum that connects to a garden hose (got mine at Walmart for about $17). The bag provided isn't enough (pressure forces dirt though it and back into water). Make two more bags- large and medium like one that comes with vaccum out of interfacing material (I think it's called Pellon- looks like my cartridge filter is made of the same stuff). Overlap the bags on the vacuum smallest to largest. Air pockets will cause it to lose suction. Just squeeze bag when that happens (not in the pool water). I've had a cloudy (above ground) pool for months and this is the only thing that has worked. You won't believe what will be in that third bag. My filter never caught that stuff.
Your filter is damaged internally and needs repair if it is a DE filter. A sand filter will pass the finer stuff back to the pool. A hand full of DE added to the skimmer prior to vacing of pool will help some. Don't understand how you could tolerate a pool that was like the above for months. Sand filters should have the ability to switch to "vac to waste" mode. You are not going to get the mud off the bottom of the pool until you replace your damaged DE filter grids
k
drain it and clean it. You should contact a pool contractor to find out if you can refill the pool and use chemicals to get the rest of the mud color off. I had to have my pool drainded and professionaly cleaned and resurfaced
To remove mud from a smimming pool is a very delicate process . There are many variables , and it can be a dangerous experience .
To prepare yourself ,
Now , you are fully equipped . Whip out your pool vacuum thing and smoke a cigarette with your bathing suit on , just to feel like a badass .
And now your pool is squeaky clean , ready for summer use .
Flac correctly and vacuum, then shock. If its really bad you might be better off emptying it
If the mud is on the bottom you can hand vacuum it to waste doing thiis wil loose you about 4 inches of water.
You can use a pool vacuum to clean dirt off the bottom of a pool. A pool vacuum clear is designed to be connected to a water source or it can be connected to your pool's circulation system.
If your pool filter is up and running, also it is best to clean the walls and floor if you have a normal to high chlorine level because this will be also your cleaning agent. Take a soft bristle brush, get in the pool and start cleaning, all the above should come off. it is better if the filter is running so you can vac out the dirt, when the dirt goes to the bottom of the pool.
Gently, with water.
I've had some success with muriatic acid- although you have to be very careful & only works if stains not too deep. They sell it in pool supplies.
If you were to use brake cleaner it will clean all the dirt and oil off of it.
If the spots are under the pool returns and you have a cartridge filter of some sort then there may be a hole in the filter somewhere or a flaw in the seal that holds it in place. If the dirt is sand and you have a sand filter the laterals in the bottom of the sand filter may be starting to wear and need replacing. A more realistic answer would be that your pool has poor circulation and those "dirt spots" are eddys where there is little circulation so any dust, dirt, leaves, bugs etc that are in suspension just drop off there and settle to the bottom. Poorly designed pool hydraulics.
If a person is fairly dirty (for example, covered in mud) then they should clean themselves off before swimming, as a courtesy to the pool maintainers. Dirt gets into the pool filters, so the less dirt in the water, the longer the filters are operational. Otherwise, that is why they get chlorinated. It is better to have the bath or shower after swimming, though.
Yes you can. I recently used it to clean my Metal Frame Intex pool. It is 12' x 30" and you couldn't aatach a skimmer and good vaccum to the filter. So I had all the dead algae sitting on the bottom and the pool still looked green. I took the Shop Vac out and cleaned the bottom of the pool with it. Just remember you can do one pass and the housing will fill with water and make sure the drain plug is removed as well as the filter.
Scrape some of it of the pool and take it to your pool shop, it sounds like it might be black algae, the shop wit have something to kill it of this is really hard stuff to kill so its good that the pool is empty.
Dirt holds moisture or water, the walls of an above ground pool are thin, yes you can put dirt around the walls, however the trade off is going to be you will shorten the length of life of the pool walls because they will rust away, so you are the one that needs to decide what you want to do, you can put plastic between the walls and the dirt or sand that will give you some extra time before the walls and frame rust away. Just a reminder from me the bottom of all most all above ground pools have dirt or sand around the bottom of the frames and a little bit of dirt on the walls you should get 5 years or a little more before the frame weakens or the side or a wall blows out. your warranty should disclose this information, or call a pool dealer in your area.
by a chemical called stain out or by using a pumice stone.
If emptying and refilling is not an option I would clean out as much debris as possible so as to not clog the filter and pump. I would then shock the heck out of it.
rain and acid wash