answersLogoWhite

0


Best Answer

First you need to take the handles and door panel off. Then you need to see whether the window has jumped off the track or if the track has come apart or is broken. If it has jumped the track, put some silicone caulk in the track and set the window back in. Make sure the track is in the down position. After replacing the window in the track, roll it all the way up and leve it for a few hours. If the track has broken, you will neew to find out where it is broken and fix or replace it. There could be a broken weld which a GOOD welder can fix for you. If you're not a professional welder do NOT try to do it yourself. It is a precision fit.

User Avatar

Wiki User

โˆ™ 2005-11-14 11:50:26
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove or fix the back right power window if it has fell down in the door?
Write your answer...
Submit
Related questions

HOW Do you set a power window back on track on a ford focus?

To set the power window back on track in a Ford Focus, you have to remove the door panel. Once you get in there, you will see the track that you will need to put the window back on.


How do you put a power window of a Chevy blazer back on track?

You will need to remove the inside door panel of your Chevrolet Blazer. Remove the window retaining clips. Put the window back into the window track. Tighten the window retaining clips.


How do you place the passenger window back in track on a 1999 Intrepid with power windows?

Remove the inside door panel of your 1999 Chrysler Intrepid. Remove the window retaining clips. Put the window back into the window track. Secure the window with the window retaining clips.


How do you manually raise power window?

I had to to take the door panel off remove the window motor raise the window then put the motor back on


How do you repair a drivers side power window of a 2001 dodge caravan which has fallen into the door?

Remove the inside door panel. The entire power window mechanism will be visible. Put the window back onto the window track.


How do you replace 1995 Toyota Celica power window regulator?

remove back seat, remove screws bottom and top of panel, remove panel. remove 3 bolts and motor arm, window and regulator will pull out.


How does one access window lock switch on 1997 Jeep Cherokee?

I'm not sure if this will help but heres what I have on power windows. lower window to down position(if you can) remove door panel remove window weatherstripping remove black window surrond(should be a screw on top of surrond towards back edge) then stationary window should unbolt then remove pins that hold operator to track pick up and pull out the operating window


Remove and replace power window motor 92 chev caprice?

cannot get motor to line back up. when I do it jams


Replacing a back window on a Monte Carlo?

How do I remove the back window in a 1998 Monte Carlo? how do I replace this?How do I remove from other Car's model


How do you install a window power lift motor on a 1993 Jeep Grand Cherokee?

i am going to be doing this this weekend....this is how my chilton says to do it lower window to down position(if you can) remove door panel remove window weatherstripping remove black window surrond(should be a screw on top of surrond towards back edge) then stationary window should unbolt then remove pins that hold operator to track pick up and pull out the operating window


How to change a power window motor in a 1999 Jeep Grand Laredo?

THIS IS ALL I HAVE...HOPE IT HELPS....SHOULD GET YOU PASSED PASSED THE WINDOW COMMING OUT. this is how my Chilton says to do it lower window to down position(if you can) remove door panel remove window weather stripping remove black window surround (should be a screw on top of surround towards back edge) then stationary window should unbolt then remove pins that hold operator to track pick up and pull out the operating window


How do you replace the window switch on a 1993 325i?

Remove the decorative cover to the window switch panel. Remove the window switch retaining screws. Remove the wiring harness from the back of the window switch. Reverse the process to install the new window switch.


How do you repair power window on a 1997 Z24?

You must first take off the door panel, by removing all door panel screws. Then you have to remove the two lower bolts that hold the window in and remove the window. Then you must drill out the rivets that are holding the power window motor in place, unplug it and remove it through one of the holes in the door ( remove the plastic covering) For re installation it is a bit tricky, have to transfer a couple parts onto the new unit with screws or rivets, and putting the window motor in, you need big rivets or possibly short bolts but they are hard to get in. Then plug it back in and put the window back in, and do up the two bolts that hold the window on. Good luck.


1995 Audi quattro power window module where is it located?

the power window module is under the dash on the drivers side below the steering wheel and it is the large on in the middle but the back side of the panel you have to remove says what each relay is for


1999 jeep grand Cherokee Laredo power front window drivers side and passengers side wont work just clicks at the switch?

this is how my Chilton says to do it lower window to down position(if you can) remove door panel remove window weather stripping remove black window surround (should be a screw on top of surround towards back edge) then stationary window should unbolt then remove pins that hold operator to track pick up and pull out the operating window


How do you get the back power window to go back up when the motor quits working?

REmove the door panel and clip the cables on the regulator.Here's how to remove a door panelhttp://www.ricksfreeautorepairadvice.com/uncategorized/remove-a-door-trim-panel-from-any-vehicle%E2%80%94-without-a-diagramHere's how to replace the regulator and clip the cablehttp://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator


On a 2000 grand prix gtp the power windows on both sides the front of the window gets stuck and the back wants to come out of the track how do you align the window to keep it in the tracks?

To align the power windows on a 2000 Grand Prix GTP, pry open the automatic window control box. Unhook the electrical connector and the mounting screws on the door panel. Remove the door panel and unhook the two linkage arms Lower the window regulator and remove the hex bolts. Finally, align the window and put back the removed parts.?æ


How do you put a driver side window back on track on a 1993 ford thunderbird?

Remove the inside door panel. The entire window mechanism will be visible. Put the window back onto the window track.


How do you remove an explorer back side door panel to see why window will not hold up?

You must remove door panel and replace window regulator.


How do you repair power window on catera?

First, remove the switch panel by prying it out and disconnecting the electrical?æconnectors. Pry away the trim panel so that you can get to the mechanical workings of the window. Remove the fasteners that hold the regulator to the door and then remove the regulator. Install the new regulator and put the door back together.


How do you remove right door panel for 1994 mustang gt convertible?

Remove armrest screws, inside handle, window crank etc. and the panal slides back about 3/8 of an inch


How do you put the window back on track in a Kia Sportage?

Begin by removing the inside door panel of your Kia. Remove the window track retaining clips. Put the window back on the window track. Secure the window with new window track retaining clips.


How do you put a window back on its roller power window?

If your window has come off its roller you will probably need a new regulator to get it back on the track. Alternatively you can try to fix it by detaching the paneling on your door and trying to get window back on roller.


How do you check your drivers side window to figure out why it is not working the window sounds like it is running but the window does not move?

HERE ALL I HAVE ON THE WINDOW HOPE IT HELPS. lower window to down position(if you can) remove door panel remove window weather stripping remove black window surround (should be a screw on top of surround towards back edge) then stationary window should unbolt then remove pins that hold operator to track pick up and pull out the operating window


How do you put a power window back on track when it has come off due to ice inside?

Roll the window about half way down, remove the door panel, take out the bolt(s) holding the window in, completely pull the window out, inspect the tracks for damage, replace if necessary, slide the window back in the tracks. There may be access holes in the door underneath the panel that will lineup with the bolt(s) holding the window in.

Study guides

๐Ÿ““
Create a Study Guide