2000-2005 Dodge & Plymouth Neons
Dodge Intrepid
Dodge Stratus

How do you remove rear speakers in a Dodge Intrepid?

959697

Top Answer
User Avatar
Wiki User
Answered
2015-07-15 21:49:32
2015-07-15 21:49:32

I was told on the first generation Inptrepid, mine is a 95. You have to remove the rear seat, then you can remove the thing that hold the speakers in.

You have to take out the top panel behind the seat in a 1994 because the bolts go from the top down but be careful the panel breaks easy!!!

Now this isn't as hard as many people think it is. It only takes a few steps, and can be finished in a matter of 20 minutes. I'll lay it out as simple as I can.

Step 1:

In a 1st generationg there are two bolts holding the bottom seat cushion down to the car body. Put the front seats all the way forward so you can have more room to work. Start off on the drivers side and kneel down on the ground and put your head in between the drivers seat and the back seat. You will see a little groove where the bolt is. Feel around with your fingers if you cant see it, you'll find it. Remove that bolt using a socket wrench, or a basic wrench if you don't have one. Repeat this process on the opposite side. Now set those bolts aside and lift up on the seat cushion, it will pop right out. Dont worry about it being heavy, its only about 5 lbs max.

Step 2:

Take ur time to clean up all the crap that has fallen between the cracks in the past years and maybe vacuum if you feel so inclined. In my car i personally found about 4 bucks in change, three buttons, about 5 pens, and an unused piece of gum, haha. After you get that done, look at the bottom of the rear back cushion when the seat belts are attached. Use a socket wrench again to remove those bolts. Once you get em out set it aside. Now move the seat belts off the seat, so they wont be pulling against the cushion and place your hands on the bottom while kneeling towards the rear of the car. This is a tricky part. You have to first pull out towards the front of the car, to get the brackets off the bolts, then lift up swiftly and strongly to lift the top brackets out of the grooves. Now keep one hand on the bottom, and move the other to the top and sort of pull out towards you while you lift up still. With a little wiggling you will get it out. Set it aside and maybe relax for a second.

Step 3:

Now you will have a perfect view of the rear deck. Now if you tug on the rear deck a little, you will notice that you have a trim panel, one on each side, holding it back. Place your fingers under this trim and just pull it out. It snaps out pretty easy, Just don't break it. Now that the trim is gone, remove the screws holding the deck in place. Now pull on the rear deck again and wiggle it around till it comes out. remember you still have those speakers back there, so if you wanna save em, don't go bashing the deck around. You could also ask someone to help and lift those speakers out from inside the trunk while you pull. Remember you still have the seat belts holding onto the rear deck so ur not ganna get too far with it unless you wanna take those off as well.

Step 4:

Now that you have it off, you can do all the work you need, whether its dynomatting, replacing the speakers, porting, or anything else that strikes ur fancy. Re-installation is the exact same as the removal. Slide the rear deck into position, and replace the trim. The re-installation of the rear back cushion is slightly tricky again, but nothing you cant handle. Hold it steady and try to look over the top of it down, and guide those hooks into the grooves, once those are in, MAKE SURE TO PULL THE SEAT BELTS BACK TO THE FRONT OF THE SEAT! I forgot to do that and it added a little time onto my re-install, haha. Push the rear seat back into the two bolts, make sure to put the seat belts back on. you will be able to tell which side was which if you just think about it. the one with the two female sockets will go on the left side of the car if us facing forward i believe, but don't quote me on that cause its off the top of my head. Once you have those on, put the nuts back on and tighten em down. Now put the bottom cushion back on and make sure the slot that is attached to the seat goes BEHIND the bracket that is attached to the car. These are the bracket that are in the front of the bottom cushion. Screw em back in and presto. You're done

All in all the procedure is pretty simple. Yeah my how to might have been long but the 1st gen needed on in here. And even though its long, its still a process that only takes 20 minutes of ur time.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


remove back seat then pull out and remove from mounting tray then that's it

Remove rear seat, them remove rear deck to get to the speakers.

The speakers in a 2003 Dodge Intrepid measure 6 3/4 inches in the front door. The rear door deck speakers measure 6 3/4 inches and the front dash speakers measure 3 1/2 inches.

The Dodge Intrepid has front and rear brake hoses

You have to remove the back seat.Remove lower seat coushin. it pulls up then outRemove back part of the coushin 2 bolts in each lower cornerremove retaining clips the hold package tray in place and remove package trayremove the speakersEasy as that :)

Remove the back seat with a number 55T torque screw socket and then you can slide out the back panel to get to the speakers.

A 1999 Dodge Intrepid rear turn signal bulb is replaced by removing the retaining screws and lifting the cover away. The bulb can then be twisted to remove it from the housing and a new bulb put in its place.

dash 3 1/2, door 5 1/4 or 6 1/2, rear 6x9

to remove the rear speakers you only have to remove the screws securing the cover of the speakers, one of them is located nearby the rear shock cover.

6 x 9 for back speakers!......... front speakers should be 6.5 and depth is at 2inches. You cant get anything that is 2inches or deeper without cutting into the car.

Begin by removing the cover from your rear speakers. Remove the rear speaker retaining screws. Remove the wiring harness from the back of the speaker. The rear speakers will come out.

Remove the cover from your 2001 Kia rear speakers. Remove the rear speaker retaining screws. Remove the wiring harness from the back of the speakers. Reverse the process to install the new rear speakers.

Remove the covers from your 1997 Nissan rear speakers. Remove the speaker retaining screws. Remove the wiring harness from the back of the speakers.

there are NO speakers in the "rear" doors of a Neon.

The Dodge Intrepid was always front wheel drive.

You will need to remove the covers from your 1996 Integra rear speakers. Remove the speaker retaining screws. Remove the wiring harness from the back of the speakers.

Remove the rear speaker covers in your 1994 Chevy Cavalier. Remove the rear speaker retaining screws. Remove the wiring harness from the back of the rear speakers.

The Dodge Intrepid does not have rear struts. This automobile has rear shocks and springs. The shocks can be removed by removing the retaining bolts on the top and bottom of the shock. Reverse the process to install the new shocks.

Remove the covers to your 2000 Chevy Malibu rear speakers. Remove the speaker retaining screws. Remove the wiring harness from the back of the speakers. Reverse the process to install your new rear speakers.

Remove the dash pad, then remove the speakers from the dash frame. For the rear speakers, open the trunk and remove the brackets, that hold the speakers in place. not for the back speakers ..you have to remove the lower rear seat then remove the seat belts then the rear seat back then remove the header panels in the back seat then remove the deck cover ..the rear speakers are bolted in from the top down under the rear deck cover....and the front speakers i believe are mounted in the door panels in the front doors ..you have to remove the door panels to remove them .some do have them in the dash also if they are there u do as the person stated before me.

Begin by removing the rear speaker covers in your 2004 Mitsubishi. Remove the rear speaker retaining screws. Remove the wiring harness from the back of your rear speakers.

u have to remove the rear deck lid, speakers r underneath how do you remove the rear deck lid on the 2005 Nissan altima

Begin by removing the covers to your 1993 Geo rear speakers. Remove the speaker retaining screws. Remove the wiring harness from the back of the rear speakers. Reverse the process to install the new rear speakers.

A Dodge Intrepid does not have a reset switch. The fuel system is computer controlled.

Driver side rear of engine block.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.