answersLogoWhite

0


Best Answer

Basically you remove the throttle body, fuel rail, and anything else that is plugging into it, then unbolt it. You need to get a shop manual however, because there is a specific bolt pattern you need to use to avoid damage.

User Avatar

Wiki User

โˆ™ 2006-11-23 14:07:09
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove the Intake Manifold on a 1997 Dodge Neon DOHC?
Write your answer...
Submit
Related questions

Where can you find a diagram for removing the spark plugs out of the back 3 behind the plenium intake manifold on a 1998 Dodge Avenger ES 2.5L V6?

You need to remove the plenium intake manifod,I have a 1997,thats how i did it.


Where is starter located on 1997 dodge neon?

It in front of the engine compartment be low the air intake manifold the starter is locate there.


Where is the fuel rail in the engine compartment of a 1997 dodge ram 1500?

It is the metal pipe that runs down both sides of the intake manifold.It is the metal pipe that runs down both sides of the intake manifold.


How do you replace a starter on a 1997 Aurora Olsmoble?

It's under the intake manifold, on top of the engine. You have to remove the manifold. Not a difficult job, but does take some time See answer to location of manifold question


Where is the starter on a 1997 Acura TL 2.5?

The starter is located on the top of the engine, on the driver's side under the intake manifold. You remove the rear manifold mounting bracket to get to it.


Where is the intake on a 1997 GMC Yukon?

intake manifold is under the throttle body


What are the intake manifold torque specs on 1997 Oldsmobile bravada?

What are the intake manifold torque specs on 1998 Oldsmobile bravada?"


Are intake manifolds interchangeable with or without egr valve on 1997 dodge 5.9 engine?

1997 does not have EGR. The 1995 and before manifold (with EGR) is different that a 1996 or later (with out EGR).


Where is the intake manifold on a 1997 mercury villager?

The Villager has an upper and lower intake manifold. It is at the top of the engine with the throttle body attached to it.


How much does intake manifold cost for a 1997?

$0 recall


Where is intake manifold runners control stuck 1996 Lincoln Continental?

where is intake manifold runners control stuck 1997 lincoln continental


What would cause antifreeze to be where your spark plugs are in a 1997 Mercury Grand Marquis?

Intake manifold gaskets are leaking, intake manifold is warped.


Where is the starter located on a 1997 Cadillac Eldorado?

under the intake manifold


Can the lifters in a 1997 ford ranger 3 liter engine be removed without removing the intake manifold?

no, u need to remove the heads to get at the lifters


How do you remove the knock sensor from a 1997 Mercury Villager?

It's under the intake manifold. The whole assembly needs to be removed, it's a complex process.


How do you replace starter on 1997 STS Cadillac?

The starter is located under the intake manifold. You will need to remove the EGR tube and the intake air tube from the throttle body. Remove the bolts around the perimeter of the intake manifold and from the passenger side of the engine compartment you can lift the intake up far enough to gain access to the starter. Remember to disconnect the battery negative terminal first. I have used a bungee cord to hang the intake in the air while working on the starter. Remove the two wires leading to the starter and then the two 13mm bolts securing the starter to the engine block. Pull the starter out from under the intake manifold and install the new starter in the reverse order. The intake manifold gaskets are reusable.


What is the torque sequence for intake manifold on a 1997 mercury cougar 4.6liter?

The 1997 Mercury Cougar 4.6 liter engine intake manifold torque sequence should begin at each end of the manifold. Keep moving towards the center and alternating from and to end.


Do you have to remove the intake manifold to change the bypass hose on a 1997 4.6 Mercury Marquis?

No, not for the hose but, I have seen the metal bypass tube that the hose connects to, rust out and cause a coolant leak out the back of the engine. The intake manifold would have to be removed to replace that metal tube.


How do I replace the intake manifold on 1997 town car?

coolant by pass hose needs repaced under intake manifold to water 1996 Lincoln town car


Where is the turbo on a 1997 Peugeot 306 1.9TD?

After the air filter and on the intake manifold


Where is the EGR valve located on a 1997 Mitsubishi Mirage?

On the 1997 Mitsubishi Mirage 1.5 liter, the EGR is located on the side of the intake manifold. You'll probably have to remove the air intake tube that goes to the throttle so you'll have enough room to reach it.


Where is the air intake sensor located in a 1997 Dodge Dakota?

The 1997 Dodge Dakota air intake sensor can be found attached to the air cleaner housing. The air intake sensor will be on the inside of the air cleaner housing.


Where is the PCV valve located on a 1997 Ford Ranger 2.3 liter engine?

On the 1992 2.3 it is behind the upper intake manifold, about even with the lower intake manifold (driver's side).This puts it between the manifold and the firewall.


Where is the thermostat located on a 1997 Dodge Intrepid Sport?

Find the top radiator hose and follow it back to the thermostat housing, which should be located towards the fron of the engine on the intake manifold.


How do you repair the intake manifold on a 1997 Blazer?

usually your intake manifold is ok...the manifold gaskets are prone to failure..they are plastic with rubber impregnated seals...if the manifold is actually pitted, you can repair with JB WELD then sand smooth.... ase master certified tech