I fohnd theres a Torx bit (t45 i think) that removes the lower seat belt mounts.. with a lot of work.. then you can remove the seat back.. and bend the rear deck carefully.. Good Luck!
When i put my Sony Xplode 6 by 9 in my 92Skylark it was a really big hassle. I hade to take my side panel that is by the passegers inside the car then you have to pull the speaker protect by poping out the pins that whole them then all you have to do is disconnect the wires and unscrew the screw, it take about a hour or two to do.
Easy; Use any available wire cutting pliers to cut the wire! It may be easier to remove the fuse for it instead, if your purpose is to remove the horn.
What kind of engine is it? I know that Chilton's and Haines manuals have the procedure. You should be able to find them at Amazon or Ebay.
To remove a magnet in a speaker, first detach the grill in the front of the speaker, second unscrew the speaker after that remove the speaker from the cabinet and cut the speaker cone. Lastly, gently discard the magnet from the speaker cone.
To remove the back seat of a Skylark, reach into the area between the back and the seat and pull up on the seat. The back part of the seat is bolted in and will require a socket wrench to remove.
Remove the rear speaker cover from your 1999 Mercury Cougar speaker. Remove the rear speaker retaining screws. Remove the wiring harness from the back of the speaker. Reverse the process to install the new speaker.
Remove speaker grill, remove screw holding speaker, screws to the mirror are behind speaker
Door Speakers: * Remove the door trim panel * Remove the speaker mounting screws * Pull out the speaker and disconnect the electrical connector from the speaker and remove the speaker Door Subwoofers: * Remove the subwoofer grille trim panel * Remove the door trim panel * Remove the 8 mounting screws from the front side of the subwoofer * Remove the single subwoofer retaining screw from the backside of the subwoofer enclosure * Pull out the subwoofer,disconnect the electrical connector and remove the subwoofer Quarter Panel Speakers: * Remove the quarter panel trim * Remove the 4 speaker mounting screws * Pull out the speaker,disconnect the electrical connector and remove the speaker Parcel Shelf Speakers: * Working from inside the trunk area,disconnect the speaker electrical connector * Remove the parcel shelf * Remove the speaker mounting screws and remove the speaker
Remove the door trim panelRemove the speaker mounting screwsPull out the speaker,disconnect the electrical connector from the speaker and remove the speakerInstallation is reverse of removal
If you follow the hose from the drivers side of the radiator, it will lead you up to the end of the thermostat housing. It is under the air cleaner. There is a lot of stuff you need to remove to get to it. Good luck.
The speaker covers are held in with a screw, remove it and tilt it out away from where the screw was. then remove the screws holding the speaker in and remove the speaker.
You do not need to remove the door panel to change your speakers. Remove the speaker cover, by prying outward on the speaker cover retaining clips. Remove the speaker retaining screws. Remove the wiring harness from the back of the speaker.
from shop manual: remove luggage cover and holder assembly remove speaker cover retainer nut and and screws securing the cover in place over the speaker assembly loosen and remove the speaker retainer screws securing the speaker in place, lift the speaker out enough to access the wire harness at the rear of the assembly disconnect the speaker harness remove the speaker installation is the reverse of removal
The 1990 Chevy Corvette front drivers side speaker cover will need to be removed. Remove the speaker retaining screws. Remove the wiring harness from the back of the speaker.
Begin by removing the speaker covers in your 2006 Toyota. Remove the speaker retaining screws. Remove the wiring harness from the back of the speaker.
REAR SPEAKER - JR41 Disconnect and isolate the battery negative cable. Fold down the rear seat backs. Remove C-pillar trim. Remove lower quarter trim behind rear seat backs. Remove fasteners from rear shelf trim. Pull out trim to access speaker. Remove speaker screws. Disconnect wire harness connector. Remove speaker (REAR SPEAKER-JR41). REAR SPEAKER - JR27 Disconnect and isolate the battery negative cable. Using a trim stick, pry the speaker grill from the trim panel. Remove speaker mounting screws (REAR SPEAKER - JR27). Remove speaker from trim panel. Disconnect wire harness connector from speaker.
The 1999 Pontiac Grand Am speakers can be removed by removing the speaker cover. The speaker cover is held in place with two screws. Remove the speaker retaining screws. Remove the wiring harness from the back of the speaker.
is there a special tool needed to remove the oil filter on 1990 buick skylark 4 cylinder front wheel drive?
Remove the speaker covers, by loosening the retaining screws. Remove the speaker retaining screws. Remove the wiring harness. The speakers will come out.
YOU WILL HAVE TO REMOVE THE REAR SEATS. THE SPEAKER GRILLS AND THE PANEL IN THE WINDOW IS ONE PIECE.
You will need to remove the rear door speaker covers. The Chevrolet blazer speaker covers are held in place with two retaining screws. Remove the speaker retaining screws. Remove the speaker wiring harness.
Remove the door speaker cover. The cover is held in place with two retaining screws. Remove the speaker retaining screws. Remove the wiring harness from the back of the speaker. Reverse the process to install the new speaker.
remove the screws usually behind the door handle, also remove the cover tabs on the door grab on the panel and then remove the speaker grill and remove the three or four screws around the speaker not the ones holding the speaker in place.
If its a convertable, remove the the screws under the rear seat and remove. Then remove the screws holding the leather enclosures and remove from sill plate. remove the speaker boxes and replace. If you don't have new speaker boxes remove cover a speaker box, access speaker and replace, you will probably have to solder the wires, then reverse the order and put back together.
Open The Door, Remove The Door Panel, Remove Speaker, Wire The New Speaker, Fix The Speaker To The Door, Refix Door Panel, Switch On
remove cover, unscrew, disconnect