Auto Parts and Repairs
Chevy Impala
Ford Expedition Eddie Bauer
Ford Expedition XLT

How do you remove the backdoor panel of a 1992 Mazda 929?

515253

Top Answer
User Avatar
Wiki User
2015-07-15 19:39:50
2015-07-15 19:39:50

The 1993 mazda's back door is attached with clasps all around the door. To remove it, simply pry around the edges. At the bottom, there is a verticle clasp as opposed to the rest which go directly into the door. This clasp has a screw which must be removed. If trying to unscrew this screw is not making progress, it may be the case that it has been stripped or rusted (mine was both). After popping all of the rest of the clasps, the panel can be lifted off of the door frame, with this single clasp on the bottom still attached. Once the panel is removed and this clasp on the bottom is the only one remaining, it can be pushed out from above.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

how to remove the door panel on a 1992 mercury cougar

User Avatar

.You can remove the door panel, from your 1992 Mercedes Benz, by gently prying on the retaining clips. There are approximately 12 retaining clips

User Avatar

You have to remove the center dash panel to get access to the bolts, screws.

User Avatar

On the passenger side, behind the plastic kick panel just in front of the door.

User Avatar

On the passenger side, behind the plastic kick panel just in front of the door.

User Avatar

Front speakers are in the door. remove screws on the door panel, then remove the panel and you'll see the speaker

User Avatar

yes, you will have to remove all the plastics from the 94 and put them into the 92, as well as the wiring.

User Avatar

Remove the 1992 Dodge Dakota inside door panel. The door handle mechanism will be visible. Remove the door handle linkage. Remove the door handle retaining bolts.

User Avatar

Were is the egr on a 1992 mazda protege

User Avatar

This should be located under the left drivers side kick panel.

User Avatar

To remove the driver side door panel on a 1992 300E all the mounting screw must be taken off. With the screw off, the remaining clips which hold the door panel need to be gently pried off. After all the hardware is removed the panel can be pulled off the door.

User Avatar

remove the door handle and window crank (you can use a coat hanger to remove the clip) remove the door lock knob. Then reach down at the bottom and pull out the panel. Install in the same order.

User Avatar

Will a 1992 mazda miata hardtop fit a 2000 mazda miata?

User Avatar

Where is the headlight relay in 1992 Mazda Protege?"

User Avatar

I have a 1992 cadillac seville. The window won't go up. The window motor is working. I want to see if the glass window itself is off the track. How do I remove the inside panel of the door to get to the glass window?

User Avatar

NO, but the entire wheel assembly will have to be removed.

User Avatar

you have to remove the whole door panel in order to gain access to the factory speakers in which should be 4x6.

User Avatar

The starter for your 1992 is located behind your passenger side wheel well. Remove tire and you will see a panel at the top of the wheel well remove it and the starter is behind that.

User Avatar

It is in the console, remove the panel where the passenger's left foot would be.

User Avatar

You will need to remove the door cards, then get to the back of the handle, should be some mounts to remove then you should be set.

User Avatar

disconnect the battery, then drop the sterring column, remove the insterment panel and the bulbs will be on the back of the insterment panel

User Avatar

The 1992 Mazda B2200 will hold close to 17 gallons of gas. The 1992 Mazda B2200 is a four-cylinder vehicle.

User Avatar

Brake fluid location in 1992 Mazda mpv


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.