Chrysler Sebring
DIY Projects

How do you remove the blower motor resistor on a 1998 Chrysler Sebring kid?

345

Top Answer
User Avatar
Wiki User
Answered
2009-04-20 18:23:31
2009-04-20 18:23:31

its under the dash on the passanger side, look for it next to the blower motor, it has 5 or 6 wires and is held into place by 2 small screws 8mm if I remember right, its a 15 min job

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


Fig 15 Blower Motor ResistorNOTE: The blower motor resistor is located on the lower right side of the heater housing.REMOVAL# Remove lower right underpanel silencer/duct. # Disconnect wiring connectors on blower motor resistor. # Remove blower motor resistor retaining screws. # Pull blower motor resistor out of heater housing.


It is behind the glove box. Remove the glove box door and there are 2 screws that hold the resistor in.


The Resistor is located on the outside of the blower motor. Have to remove the blower from under the glovebox to get to it. The Resistor is located on the outside of the blower motor. Have to remove the blower from under the glovebox to get to it.


The a/c heater blower motor resister is located in the vehicle on the passengers side inside the housing next to the blower motor...............Remove the blower motor resistor wire harness connector.Remove the blower motor resistor screws.Remove the blower motor resistor.


# Locate the blower resistor under the right-side of the instrument panel # Disconnect the electrical connector from the blower motor resistor # Remove the blower motor resistor mounting screws and remove the resistor from the housing # Installation is the reverse of removal


Pull out the lock on the blower motor resistor wire harness connector to unlock the connector latch . Depress the latch on the blower motor resistor wire harness connector and disconnect the connector from the resistor. Remove the two screws that secure the blower motor resistor block to the HVAC housing. Remove the resistor block from the HVAC housing............


On my 2002 it is mounted in the blower housing that is on the front passenger side above where the foot area is, may have to remove a panel to see it, some wires are plugged into it and two screws hold it in place. When mine failed only the hi speed setting would work.


the blower fan resistor is located in behind the glove compartment to the left of the blower motor. you have to remove glove compartment to get at resistor.


You have a bad blower resistor. it is located directly behind the blower motor on the passenger side of the vehicle. You must first disconnect blower motor from bad resistor. Lower and remove blower. It won't be easy but remove the screws holding the resistor, disconnect the resistor and remove it. Cost is approximately $40 for a new one.


It's right behind your glove box. My kids replaced it. Remove the glove box. It's easy to unplug and plug in the new one. Approx $80- 100 from your Chrysler dealer. ( If it fails your blower works on its default with fan at full speed and not adjustable ) That is the front blower motor resistor which is located behind the glove box; the rear blower motor resistor (for cars equipped with the rear blower switch) the resistor is located below the final rear passenger window, to the right of the bench. In order to gain access to it you will need to remove the bench and a few trim pieces.


A blower resistor can be replaced, in your 2002 Oldsmobile, by removing the resistor wiring. Remove the retaining screws. Reverse the process to install the new resistor.


Blower motor: remove the glove box and you will see the blower motor and blower resistor.


Locate the resistor under the hood near the blower motor on passenger side firewall. Unplug the electrical connector. Remove the screws holding the resistor in place. Remove the resistor. Install in reverse order.


You must remove the glove compartment door to access the blower motor. On top of the blower motor will be wires connecting to the top. Release the connecter and let it dangle. Then using a screwdriver, remove the blower resistor on top, where the wires connected, and replace with a new resistor.


BradleyWhat does a 2002 Chrysler sebring blower resistor look like? Where is it look locate? Blower Motor Resistor Replacement (with pics)I knew I had to change the blower motor resistor because on my '02 Sebring LX the 1-2-3 options on my fan didn't work, and 4 did. So I did a little bit of researching (mainly on this forum and a few other Chrysler pages) and went straight to the dealership.I bought my replacement from Pep Boys for 42.00 USD.This is what you should be looking for:To get to this, I recommend moving your passenger seat all the way back (as well as tilted all the way back).. Under my glove-box there was a foam'ish covering being pretty much held on by one bolt, remove it.Now you should have access to your blower motor resistor and a whole bunch of other fun, colorful wires. Lol, something like this:Just remove the two bolts holding in the resistor, it should slide right out. But this is where I encountered quite the obstacle. Getting to the 2nd bolt was hell, as it's conveniently hidden 'on the other side' of the resistor out of reach from anyone with big arms/shoudlers/hands. Anyway, replace the old with the new (in the same slot of course).Put bolts back on, foam'ish cover back on, and you're done!"The OE Manufacturer has modified this resistor to a heavier duty style. The opening in the housing must be modified to accpet this new part. Disconect the wire harness connector from the blower motor resistor, Remove the two screws that secure the blower motor resistor to the HVAC housing. Use a hot knife or similar tool to enlarge blower resistor opening in the HVAC housing so that the opening matches the inside edge of the raised rib around the opening (fig. 1).Note: Remove any/all debris from thw HVAC housing before installing the new resistor.Remove all material in the shaded area."The note of course refers to Fig.1.Whole job took 1 hour. I suppose I'd have save some time had I read the instructions prior to removal/installationJ


Safety Tip: Always wear safety glasses when working on your motor. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or closed toe shoes. 1.Remove the negative battery terminal. 2.Locate the blower motor resistor on the passenger side under the dash board. It is mounted to the the blower housing near the blower motor. 3.Disconnect the electrical connector to the blower motor resistor. 4.Remove the screws or bolts to the blower motor resistor and remove the resistor. 5.Installation is the reverse of the removal.


To change the blower motor resistor in a 2002 Nissan Maxima, locate the blower motor resistor under the glove compartment on the passenger side of the vehicle. There is a clip that is depressed and then the resistor will slide out. Remove both ends of the resistor and then replace with the new resistor.


The heater core can be removed from a 2001 Chrysler Sebring by taking it off its mounting. This is done by removing the dash.


Remove the positive battery cable from your 2001 Chrysler Sebring battery. Remove the cables from the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.


Disconnect the battery negative cable. !!!Power is still on when ignition switch off!!!I have Olds Intrigue 2000. Blower control resistor (Controller) located behind theblower motor. Very close to the firewall, and it is a pain in the neck to get there.Using 5.5 mm. socket remove the blower first. (3 screws are holding the blower)Using the same socket (5.5 mm) remove one visible screw which holds the resistor.You will have to loosen two other screws located between the resistor and firewall. You don't need to remove them completely, just loosen them! Resistor just slides outwhen they loose.---------------------------------------------------------------------------------------------------------Disconnect the battery negative cable.Remove the RH instrument panel insulator retainers. Adjust the carpet for access.Disconnect the courtesy lamp from the instrument panel insulator by turning 1/4 turn counterclockwise.Remove the RH instrument panel insulator.Disconnect the electrical connectors from the blower motor resistor.Disconnect the blower motor resistor electrical connector from the blower motor.Loosen, do not remove, both forward screws. The blower motor resistor opening is slotted as access is extremely limited.Remove the rearward screw.Remove the blower motor resistor.


The resistor is located to the lower right of the blower motor. You will need to remove the battery to access it


heater blower resistor has to be replaced. you have to remove glove boxthe resistor is to the right of the heater blower moter


The blower resistor is located under the dash, near the floor, on the passenger side of the vehicle. I had to replace the resistor about a year ago. It is not an easy place to work in. You have to remove the blower unit in order to get at the resistor. Not fun, but rewarding when you actually do it yourself.


On the passenger side, bend under the dach, disconnect the coupler, remove the screw of the small hexgonal part and remove the blower motor resistor!


Remove plastic air duct from under passenger side dash, and you will see a white ceramic rectangular resistor with a couple wires sticking out on the firewall by the blower motor cover. Remove screws on the resistor and remove wires to replace.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.