Remington Firearms
Marlin Firearms
Motocross

How do you remove the bolt on a lever action?

575859

Top Answer
User Avatar
Wiki User
Answered
2009-03-18 19:06:04
2009-03-18 19:06:04

be shure gun is unloaded ! pull the hammer back to full cock. open lever about 1/3 and remove the screw that holds the lever in (pivit screw),remove lever handle. pull bolt out slowly (may have to hold hammer past full cock). the ejecter spring is under presure but pulling the bolt out slowly will release the presure remove the bolt remove the ejector spring with a small pair of neddle nose pliers or nimble fingers. on assembly be shure install ejector spring in the hole and hold it their with a finger and install the bolt to hold it in place. the rest is just reverse directions. good luck. Go to the following webb site to see a diagram and instructions....it might help along with the previous advice........ http://www.urban-armory.com/diagrams/marlin33.htm If it is a 39A model, put on half-cock safety, unscrew the takedown screw, separate the two halves of the gun (they may be stuck together pretty well. Lay gun on your lap, with the receiver flat lever towards your knees - smack receiver with the palm of your hand to the right of the half-moon shape seam. Make sure your knees are far enough apart that the gun can "fold" in the center. Once halves are apart bold can be easily removed. On newer models there is a screw or pin that keeps it from falling out, on my older 39A the bolt practically falls out.

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


You do not want to try this. Find a qualifed Browning gunsmith.


Remove the bolt in the lever perch. For a clutch lever, loosen the cable enough to remove the broken lever and replace the new one. Adjust the clutch cable back and replace the bolt in perch. For the brake (disc brake)) lever, you simply remove the bolt and replace lever, put the bolt back in the perch and you're done. If you have drum brakes, it is the same as the clutch lever routine.



In a fire usually = worth nothing. You will have to replace. Donate to a museum. Never seen a rifle that was both a lever and a bolt action.


WHICH MODEL, BOLT ACTION, LEVER ACTION ,SEMI AUTO???????????


Take the barrelled action out of the stock, and at the front left side of the reiciver there is a little release lever, pull it down and remove the bolt while holding trigger back.


No, bolt-action only. Bummer! I was under the impression that they did some years back but discontinued the 35 cal. lever action rifle by Remington


move the safety lever and hold trigger back as you remove bolt


Push the lever next to it as u pull the trigger then slide it out


Push the safety lever fully forward to dis-engage the bolt stop. Then the bolt can be removed rearward.


loosen the bolt on the lever, remove the lever and replace in the new angle, then retighten.


rifle or shotgun that cycles the bolt by means of a lever. The old cowboy guns you see on TV is an example.


I'm not familiar with a "Winchester model 77". Is this a bolt action gun or a lever-action rifle? Winchester's famous bolt-action hunting rifle is called the Model 70. Their most famous lever-action guns are the 1873 and 1894 models. Ruger is a company that has a bolt-action rifle called the Model 77.


Remove the stock and you will see what is keeping the bolt from sliding out.


They are usually broken out by the type of action- break open, bolt action, lever action, pumps, automatic, etc. AND- the muzzleloading rifle.


First remove the screw opposite the bolt. Operate the bolt as if you were cocking the gun, pull the trigger and it will slide out.


There ARE bolt action shotguns and handguns, such as the Mossberg 183 or the Remington XP-100- but they are not common. Lever action shotguns and handguns are also pretty rare.


Bolt action came first. It was first produced in 1824, whereas the lever action didn't go into production until 1860. A2: The lever action Volcanic was in limited production in the 1850's. Its design was "borrowed" by Henry, and then, Winchester. There were others, like Spencer; and single-shot levers like Sharps were made during around the civil war . Levers are usually not as strong as bolt actions and can't take as powerful cartridges.


You make sure the gun is unloaded. Open the bolt. When the bolt stops, look at the lower left of the bolt and you will see a small lever next to the extractor. With a small screwdriver, press the small lever down and at the same time pull back on the bolt, The bolt will slide right out.


On what bike? There might be a bolt to unscrew for the front brake, make sure the new lever abuts the hydraulic actuator correctly. For the rear lever: Mechanical brake, undo and remove the linkage from the lever. Remove the pivot bolt and withdraw the lever and return spring. Refit is the reverse, ensure all locking pins and springs are refitted. Hydraulic is different in that there is no linkage, a small pin acuates the hydraulic piston. Remove the pin connection and proceed as before.


its a bolt action and they are worth about 150.00 or so in good condition


Do you have the pump shotgun or the lever-action rifle?


Pull and hold the trigger, then pull the bolt back and it should release.


When u pull the bolt back almost all the way, there is a little lever that pops up, which u have a push down as u r slowly pulling the bolt to get the timing right; just use a small screwdriver i did it and it was easy. pull the bolt out/push in a few times and watch in the action when the bolt comes out good luck


Actuate the bolt to the rear and there is a tang in front of the trigger that hangs down..Press up on this tang and pull the bolt back and it will remove it from the action.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.