you have to remove to entire headlight assembly 2 screws on top and 2 nuts on the backside of assembly that go through metal panel
detach the bulbs and remove the clips behind the headlight assembly
unhook 6 black slide clips from top of grille, and 5 black slide clips from bottom of grille, and remove chrome trim screws (4) from headlight assembly and unplug headlight and swap it out. assembly is reverse of removal.
Open the hood of the engine compartment to your 1994 Toyota Corolla. Remove the wiring harness from the headlight. Remove the headlight retraining bolts from the headlight assembly. Reverse the process to install the new headlight.
Remove the parking/turn signal light assembly. Take off the grill. Remove the headlight bulb. Remove the inner and outer attatching screws and upper attatching screw. Lift the headlight out.
Disconnect the battery and open the hood. Reach the headlight from the back and disconnect the two wires. Remove clips holding the assembly. Remove the assembly carefully and set it aside. Install the new one.
for a 1994 Grand Caravan (probably like the 1995) see: How do you replace the headlight assembly located on a 1994 Dodge Caravan? for a 1994 Grand Caravan (probably like the 1995) see: How do you replace the headlight assembly located on a 1994 Dodge Caravan?
You need to remove the side marker first. Remove the screw and pull hard perpendicular to the car to remove the side marker. Once that's removed you can see 2 screws on bottom of the headlight/foglight assembly and one screw on the top of the assembly as well as one nut on the side of the light assembly. Remove those screws and nut and you can pull out the whole headlight/foglight assembly. Remove the connector by pulling it straight out. Remove the rubber gasket and the spring lock. Assembly is the opposite.
To remove the bulb- raise hood reach behind headlight housing grasp the bulb holder assembly and rotate counterclockwise and gently pull straight out.There are two bulbs to each headlight assembly. Note.... do not touch the new bulb lense with your fingers.The oil in your skin will cause a hole to burn in the halogen bulb. If you do touch the bulb,clean with alcohol before installing. To remove the headlamp assembly- Raise the hood and remove bumper cover screws and remaining bumper cover screws.Then remove the electrical connection from the back of assembly.Then remove the 4 screws retaining the head lamp assembly and remove the assembly.
To change headlight in a 1994 Mazda 121, undo the top mounting screw. Slide a flat screwdriver behind the assembly abd pop out the fitting. Repeat with the other side to pop the other bayonet fitting and remove the old headlight.
I detail used cars at local dealerships and I have restored many Caravan headlight lenses. I use a product called Crystalenz, it works great and is really easy to use. You DO NOT have to replace the lenses. Check out their website www.crystalenz.com for more info. for removal, see: How do you replace the headlight assembly located on a 1994 Dodge Caravan?
There is 2 large plastic screws that hold the headlight assembly`s in. Simply unscrew them and lift the headlight assemblies out then unhook take the bulbs out.
For the 1994 model (B3000), you can't change just the bulb. You have to change the headlight assembly.
Do you mean the side marker light next to the headlight? Open the hood. On top of the headlight assembly, there's a screw with a Phillip-head pattern, next to the marker light. Remove the screw. Pull the marker light forward to remove it.
For the rear... Remove the plastic nuts that hold the carpet on(behind the tail lights) and then you can easily remove the bulbs For the Front... You have to remove 2 bolts (that have plastic heads that your can turn with your hand) and remove the entire headlight assembly on that side
between the back of the headlight and in front of the head light panel,you reach you hand between the lil space there is 3 clips black.1 on the point of the headlight and 2 on the opposite end for the top and bottom,the light will slide right out.
I just tried to pull headlights from a 1994 Avenger yesterday. Did you have the same problem as me that the bolts on the inside near the radiator were impossible to get free?
Reach behind the light assembly and unplug the connector, using a screwdriver to hold the clip out of the way. Turn counter-clockwise to remove the assembly. Push in and counter-clockwise to remove the bulb. Installation is opposite. From my HAYNES manual.
you have to remove the head-light assembly to get the turn signal bulb front and rear lights The side light has one screw on top to the outside of the headlight assembly holding the cover in place.
there is a pin on the switch which must be depressed to remove the unit from the dash.
Remove the 4or5 screws along the top of the trim plate, the trim plate should pull off,the headlight switch is attached to the trimplate.
Unbolt and remove everything bolted to the inner fender. Starting behind the headlight assembly, remove most of the bolts all of the way around the fender. With one or two helpers, hold the fender on while removing the remaining bolts, then the fender can be lifted off.
You may have to remove various covers in the engine compartment to get to the adjusting screws on the back of the headlight assembly. Best left to a professional who will properly aim the headlamps so that they do not blind oncoming traffic.
Remove the indicators to access the side bolt holding the headlight then remove the two top bolts, slacken the nut accessed through the hole at the inner edge of the headlight. this should release the headlight enough to disconnect any wiring and then the headlight is free.
To replace the headlight bulb in a 1994 Nissan Sentra first prop the hood of the car. Locate the headlights and remove the bulbs from the housing. Install the new bulbs.
You have to remove the strut assembly from the car, and need the spring compressor to remove the spring to remove the shock.