0
How do you remove the climate control bezel from a 1999 Civic?
Wiki User
∙ 14y ago
Remove the two Philips screws on the panel where the 12v aux input is at.
Remove the four 8mm bolts that hold it in place.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you remove radio climate control bezel from the civic 2000 ex?
Remove the two Philips screws on the panel where the 12v aux input is at. Remove the four 8mm bolts that hold it in place.
How do you remove the dash to get at the stereo?
According to my Haynes manual all you have to do to get at the stereo is remove the center bezel. that is the plastic panel covering the area around the stereo and the climate controls. just grip the plastic between the radio and the climate control panel and pull. make sure to unplug the electrical connector for the courtesy light before you fully remove the bezel.
How do you remove the stereo in a 2002 Honda Civic?
2001-2002 Honda civic radio removalStart by removing the cigarette lighter panel. Insert a hook tool behine the panel and pull outward to release the retainer clips. Inside the panel opening at the top are two 8mm.hex head bolts that hold the bottom of the radio inplace. Next remove the trim bezel around the radio/climate control module. Insert the hook tool under the bezel and pull firmly. Work all the way around the bezel to release all the clips. Pull the unit out and remove all the wiring conectors. Now you have four 8mm. hex head bolts to remove and your radio is out.
How do you remove the front ceiling console on a 2002 Expidition?
Control Panel Front 1. Disconnect the negative battery cable. 2. Remove the overhead console retaining screws. 3. Carefully release the three clips and slide the overhead console forward. 4. Detach the panel electrical connectors. 5. Remove the panel retaining screws. 6. Remove the auxiliary climate control panel assembly from the bezel. 7. The installation is the reverse of removal. Rear 1. Slide the auxiliary climate control panel assembly forward and downward. 2. Detach the electrical connectors. 3. Remove the auxiliary climate control panel assembly from te bezel. 4. Detach the electrical connectors. 5. Remove the screws. 6. Remove the climate control panel assembly. 7. The installation is the reverse of removal.
How do you remove the overhead console on a 2005 expedition?
Control Panel Front 1. Disconnect the negative battery cable. 2. Remove the overhead console retaining screws. 3. Carefully release the three clips and slide the overhead console forward. 4. Detach the panel electrical connectors. 5. Remove the panel retaining screws. 6. Remove the auxiliary climate control panel assembly from the bezel. 7. The installation is the reverse of removal. Rear 1. Slide the auxiliary climate control panel assembly forward and downward. 2. Detach the electrical connectors. 3. Remove the auxiliary climate control panel assembly from te bezel. 4. Detach the electrical connectors. 5. Remove the screws. 6. Remove the climate control panel assembly. 7. The installation is the reverse of removal.
Removing the console on your 2007 expedition?
Control Panel Front 1. Disconnect the negative battery cable. 2. Remove the overhead console retaining screws. 3. Carefully release the three clips and slide the overhead console forward. 4. Detach the panel electrical connectors. 5. Remove the panel retaining screws. 6. Remove the auxiliary climate control panel assembly from the bezel. 7. The installation is the reverse of removal. Rear 1. Slide the auxiliary climate control panel assembly forward and downward. 2. Detach the electrical connectors. 3. Remove the auxiliary climate control panel assembly from te bezel. 4. Detach the electrical connectors. 5. Remove the screws. 6. Remove the climate control panel assembly. 7. The installation is the reverse of removal.
How do you change the in dash heater control on a 1998 Chevy blazer?
Remove the two screws at the top of the instrument cluster. This will allow you to pull out the entire bezel. Pull out the bezel, and pop the switch out from the bezel.
How to replace climate control unit on 2001 Chrysler sebring?
1. Remove the center "bezel" by removing two screws on the bottom. The bezel will now snap out when pulled out. 2. Remove the radio. The radio is held in by 8 screws. Disconnect from antenna and wiring harness. 3. The climate control unit is now exposed. Remove the four screws holding it in the bracket. 4. Remove the air control door cables (two of them). Depress the clips while pushing the eye hole up. This is very tricky and tale patience. 5. Disconnect the wire connectors. 6. The units should now be ready to remove. 7. Installation is much simpler. Reverse steps 6 to 1.
How do you change the light bulb for the heater control on a 2006 Tahoe?
To change the light bulb for the heater control on the 2006 Tahoe, you will either need to replace the entire climate control panel or remove and re-solder the bulbs. You can remove the bulbs by first removing the dashboard bezel and then the dash itself. Access the bulbs and pull them out of the control panel. Solder new bulbs into the panel.?æ
How do you replace temperature control panel in passat?
Detach the negative battery cable. Remove the bezel to get access to the control head and remove its screws. Remove the control panel. Pry the clips free. Disconnect cables from the heater. Install the new control panel.
How do you remove the Pontiac Vibe radio?
Caution: The air control bezel uses a thin plastic overlay fixed onto an open frame. The radio bezel has locking ribs on the bottom- when removing the radio bezel, the ribs can puncture the air control bezel. Place a piece of heavy tape or carboard over the air control bezel to protect it. Use a thin plastic tool to pry the bottom of the radio bezel until it comes loose. Then work around the sides until the bezel separates from the dashboard. Unplug the connectors at the top. It will be attached by the AC harness- remove the connector (which can be a bit tough) or just flip the bezel over the steering wheel. Remove the three 10 mm bolts that hold the radio. Remove the radio and unplug the connectors from the back. GM radios are a double DIN style, so most replacements will need an install kit that will add a blank plate or storage pocket.
How do you replace the bulbs in the climate control control box on a 2002 Honda Accord?
To replace a Honda Accord EX 2002 climate control light you have to detach the bezel - a black plastic frame that covers the clock and hazard lights switch, the vents, the climate control unit and the audio system. Note that the climate control unit and the vents are actually attached to the bezel from behind and come off with the bezel as one part, so do not attempt to separate them! You will need small tweezers, a small flat screwdriver and a rather long Phillips one (and the replacement light bulb of course). The bulbs are accessed from the back side of the climate control unit. # Disconnect the negative battery terminal. # With a small flat screwdriver pry out the clock and hazard lights switch unit from the bottom. It comes off easily. Disconnect the unit from the wires. # Unscrew and take out the screw behind the clock that holds the bezel in place. Be careful not to drop it. (Take a string and tighten a little noose around it when unscrewed for quarter of an inch or so.) # Unscrew the 2 screws at the bottom of the bezel that hold it from below. # Pull the bezel straight towards you (this is the hard part). There are 3 spring-loaded holders behind the bezel which has to be snapped out. The bottom side of the bezel separates easier (being held with just one spring); once it separates stop pulling on it (lest you break the bezel) and pull on the upper side until it also separates. When done, check the little steel springs that are snapped on the 3 protruding parts of the bezel. If misplaced snap them back in place. Disconnect the climate control units from the wires. # Put the bezel face down on a soft surface. Take out the burnt bulb by turning it 45 degrees counterclockwise with a small flat screwdriver and pulling it out with tweezers. Insert the new bulb and secure it by pushing on it and turning 45 degrees clockwise with the screwdriver. # The reassembly order is quite obvious: connect the climate control wires; snap the bezel in by pushing gently but firmly; insert and tighten the 3 screws; reconnect the hazard lights switch and the clock; snap back it; reconnect the battery negative terminal.
