answersLogoWhite

0


Best Answer

Perplexing ins'nt it. I took me two hours to figure this out. You need to make a bracket. It attaches to one one of the four bolts behind the fan which holds the pully on. The other end of bracket gets attached to the cloest alternator bolt. I used a 1" wide X .09 thick steel bar stock. As you can tell, it's not a straight bar when you finish making it. Bend it in a bench vise and drill the clearence holes to fit the two bolts. You will need it to replace the fan assembly also. Hope this helps.

User Avatar

Wiki User

โˆ™ 2005-10-01 01:43:01
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you remove the clutch fan nut to replace the water pump on a 1999 Safari is it reverse threaded?
Write your answer...
Submit
Related questions

How do you replace a clutch in a 1995 s10?

Remove the transmission. Remove the clutch plate and springs. Remove the clutch. Reverse the process to install the new clutch.


Is the bolts on the water pump pulley reverse threaded?

no they are not! the only bolt that maight be left tread is the fan clutch and only on some models not all.


How do you replace the fan clutch on a 1999 Tahoe?

Remove the fan belt, by loosening the tensioner pulley. Remove the fan clutch with the retaining bolts. Reverse the process to install the new fan clutch.


Replace clutch cable on a sportbike?

Replace clutch cable on sportsbike


How do you replace a throw out bearing in a BMW 330ci?

To replace a throw out bearing in any car or truck you must remove the gearbox, then remove the clutch, then pull the bearing out of the flywheel and replace it. Assemble in reverse order.


How do you replace a clutch cable on a 1997 Plymouth Breeze?

Pull out the old one...remember how you did such. Put in the new one in reverse order.


How do you get the fan clutch off of a 1999 gm safari to replace the water pump?

fan clutch screws off water pump fan pump has left hand thread so to remove you need to turn clockwise


What is the cost to replace a clutch in a BMW z3?

what is cost to replace a clutch in a BMW Z3


Clutch adustment 1980 GMC k1500?

There should be a threaded rod that goes from the clutch fork to the linkage arm, this can be shortened or lengthened as needed.


What is problem when car won't go into reverse?

Bad reverse clutch in the tranny


Replace a clutch on the Renault clio?

how long will it take to replace the clutch in my 2002 renault clio


How do you replace the clutch pedal position switch on a1996 dodge Dakota?

Rotate the switch on the rod for the master cylinder for the clutch. Take out the retaining clip. Remove the clutch pedal position switch from the rod. Disconnect the electrical plug. Plug the new clutch pedal position switch in and installation is the reverse of removal


How do you put a Ford Fiesta into reverse?

easy you get the gear stick and on there underneath the stick will be a little clutch button of sum sort and then you put into reverse along with the clutch in


Where is and how do you replace 91 Mazda 626 DX clutch slave cylinder?

The clutch slave cylinder on a 91 Mazda 626 DX is located on the clutch bell housing. To replace the unit, first remove the hydraulic line and turn the line cap counterclockwise. Remove the two bolts holding the slave cylinder in place. Reverse directions to install new unit.


How to Replace clutch master cylinder f250 7.3 duper duty?

You can replace the clutch master cylinder, on your Ford F250 7.3 liter super duty truck, by first removing the hydraulic line. Next, unbolt the master cylinder. Reverse the process to install the new master cylinder.


Mazda b3000 clutch working in upper gears but not to lower gears or reverse?

get a new clutch


What are symptoms that the clutch need to replace?

Difficulty shifting, can't reach first gear and grinds to reverse, have to stomp on the brakes to downshift, basically any sort of unusual difficulty with shifting, car jumps forward when clutch is engaged or moves while on a flat surface and clutch is engaged.


What do you do if your 89 Nissan Sentra clutch pedal quit working and you could not get it in gear but you forced it into reverse and now it is stuck in reverse.?

If a 1989 Nissan Sentra clutch pedal quit working and the car is now stuck in reverse, it will need to be towed to a repair shop to fix the clutch. The transmission may also be damaged due to it being stuck in reverse.


How do you replace the AC compressor clutch on 2006 Jeep Liberty?

how do you replace the AC compressor clutch on 2006 liberty


Mazda 1987 truck will not shift into any gear but reverse?

Well you have a strange issue. Being the trans will not shift into any but reverse would point to the clutch being toast. Normally if the truck will not shift is the slave clyinder or even the clutch master or throw out bearing gone. To rule out the the throw out did it noise while the truck was in neutral and even while in gear.If either apply may be the throw out is gone, but sounds 100% clutch is gone. If the truck will shift into soley reverse then this would rule out the slave, and clutch master cyldr and even the throw out in most cases due to the it is moving the fork to engage the clutch and the surface of the clutch is worn to it's life except reverse due to it is not used as much. I recommend a new clutch and replace the throw out bearing and would be a good idea to replace the pilot bearing and go ahead and do the rear main seal even if its not leaking if its got lots of miles, plus the age would make me do it being you have the trans pulled out.


Mazda mx3 v6 clutch problem?

Keep It Simple Stupid. Take it to a mechanic and replace clutch cause any clutch problem means you need to replace it!


How do I replace a clutch in 2000 Pontiac Montana?

It's an automatic, there is no clutch.


2002 kia spectra reverse is sluggish and jumps when put in reverse from park?

it is the reverse clutch in the transmission.around 1000 to 1800 to repair it.


Where is the clutch adjustment on a 1999 Dodge 2500 truck?

Clutch slave is seled unit. replace clutch


When should you replace the clutch on M3?

The clutch should last approx 150,000 miles. There is no need to replace this if it isn't abused