answersLogoWhite

0


Best Answer
Copy

Go to this website: - click on "Resources" on the left.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:18:19
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you remove the dash-instrument cluster on a 1991 GMC Sonoma to change the lamps?
Write your answer...
Submit

Related Questions

How do you fix the light on the odometer?

Remove the dash cluster to gain access to the back of the cluster to change the bulbs.


How do you change the bulb for dash lights in 2000 dodge durango?

Behind the instrument Cluster. Or remove it and replace the Cluster.


How do you change the light cluster on a Mazda 323f w registration?

To change the rear light cluster, first gain access to the boot, then remove the three plastic covers located directly behind cluster in boot these give you access to three 10mm nuts. To remove these nuts you will need a 10mm socket and a medium reach extension bar, remove all three nuts being careful not to drop them and the rear cluster will come away from body work then remove the lampholders to remove cluster completely. This is also how you would change a bulb in the rear cluster if you need to.


How do you change a Chevy S-10 instrument panel light?

remove the trim panel around the instrument cluster then remove cluster. On the back of instrument cluster are the bulbs just turn them half a turn and they come right out.


Do you have to remove engine in a 97 gmc sonoma with a 2.2 4 cylinder to change oil pan gasket?

No


What would cause the speedometer to stick on a 2004 cavalier manual trans how do you change the cable?

remove cluster fuse to reset cluster....if still not working properly replace cluster


How do you change the heater blower motor on a 1995 gmc sonoma?

remove the right side of the dash, remove ductwork. its behind the glove box


How do you change rear light cluster on a grand scenic 05?

open the boot you will find 3 screws undo them then ease the cluster away from body then remove the bulb cluster its easy to do


How do you change the high beam warning light on a elantra?

If you mean the bulb in the dash indicating your high beams are on, you need to remove the instrument cluster. Depending on the year of the car, you remove the instrument bezel cover, usually a couple screws under top edge of cluster, then remove the cluster. These screws are usually 2 at the tope and 2-3 at the bottom of the cluster, then remove the cluster, disconnecting 2-3 harness clips and the speedo cable if not equipped with digital speedo. Bulbs plug into back of cluster. Change them all if one blew out the others are not far behind and not very expensive....


How do you remove the instrument cluster in a 1997 Nissan Maxima GLE?

* Disable the airbag system * Remove the instrument cluster bezel * Remove the retaining screws and pull the cluster forward * Unplug the electrical connectors and remove the cluster from the car


How do you change fuel vapor sensor on a 1997 gmc sonoma?

To change a fuel vapor sensor on a 1997 GMC Sonoma you need to disconnect the wires that are holding it in place. Next, remove the old sensor and replace with the new one.


How do you change a light bulb on the fuel gauge of a Ford Freestyle?

Remove 2 7mm bolts on instrument cover plastic. remove this part exposing the 4 7mm bolts that hold in the cluster then carefully remove instrument cluster from dash. On the back of the cluster you can remove the bulbs by turning them counter clockwise and pulling them out. Bulb number 194


How do you remove the instrument cluster on a 97 Malibu?

To remove the instrument cluster on a 97 Malibu, first remove the screw at the bottom right of the radio's molding. Then remove the molding and the screws under the steering wheel. Remove the entire molding surrounding the cluster and the four screws to remove the entire instrument cluster.


How do you change the dashboard light bulb on a 1990 Toyota Corolla?

You have to remove the instrument cluster to get to the bulb. start by removing the left speaker grill, lower left trim panel (5 screws), remove the steering column trim cover (6 screws), remove the cluster and trim bezels (9 screws), Remove the cluster by pulling it out ( 4 screws).


How do you remove the instrument cluster in a 2003 aurora?

Remove instrument cluster in a 2003 olds aurora


How do you change a rear light bult on a Renault Scenic?

depends on the year on a 2005 you have to remove the rear cluster.


Is there a way to change an odometer?

Sure, but at some effort. You need to remove the instrument cluster from the dash to replace it.


How do you change the tail light and brake light in a 2005 a4?

IN THE TRUNK, REMOVE PANEL NEAR REAR LIGHTS. IF THE BACK OF THE BULBS ARE VISIABLE THEY ARE EASY TO REMOVE. IF NOT, CHECK FOR SCREWS THAT HOLD THE TAIL LIGHT CLUSTER IN PLACE. REMOVE SCREWS, REMOVE CLUSTER, REMOVE BULB. I HOPE THIS HELP. GOOD LUCK.


How do you replace the hi-beam indicator bulb in the instrument cluster?

You didn't mention the year, make and model vehicle but I would imagine you will have to remove the dash cluster to gain access to the rear of the cluster to change bulbs.


How do you remove a 1992 Honda Accord dashboard?

Remove the vents and screws under the ac cluster speedometer cluster.


How do you remove the entire dashboard on a 1992 accord?

Remove the vents and screws under the ac cluster speedometer cluster.


How do you remove the instrument cluster on a 2002 explorer?

Disconnect negative battery cableTilt the steering wheel to its lowest position and remove the instrument cluster bezelRemove the instrument cluster retaining screwsPull the instrument cluster out,unplug the electrical connectors from the backside and the shift indicator from the bottom (automatic trans models) then remove the cluster from the instrument panel


How do you change the overdrive light on a 98 villager?

You will have to remove the instrument cluster. This may be an LED that should never have failed.


How would you remove a OES Linux node from the cluster?

Remove the node from the existing cluster.Do a "cluster leave" on the node you want to remove from the cluster.In iManager go to cluster options and delete the cluster server object that represents the node you wish to remove.Clean up the old configurationFind out your current version of novell-cluster-services with"rpm -q novell-cluster-services" Make sure you know this version when it comes to reinstalling.Remove the novell-cluster-services rpm ie. (rpm -e novell-cluster-services-1.8.2.276-2)Delete all files in /etc/opt/novell/ncsDelete the /etc/sysconfig/NCS file


How do you get to or where are the instrument lights on your 89 Toyota 4x4 pickup?

Remove the dash and remove the instrument cluster, the lights are in the back of the cluster.