Chevy Celebrity
Dodge Intrepid
Ford Expedition Eddie Bauer
Grand Am SE

How do you remove the dome light housing to replace the bulb on a 2000 Dodge Intrepid?

212223

Top Answer
User Avatar
Wiki User
Answered
2005-12-05 04:31:57
2005-12-05 04:31:57

pull the whole light down from the head liner (it is just held on by 2 clips it will not break )then you pull the light itself from the holder change it and reinstall the complete light assy. to the head liner

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Unlike other cars, the Intrepid requires you to remove the entire headlight housing. This is very simple, there are to long bolts on top of the housing that hold the housing on. Simply remove these bolts, untwist the bulb, replace the bulb.

A 1999 Dodge Intrepid rear turn signal bulb is replaced by removing the retaining screws and lifting the cover away. The bulb can then be twisted to remove it from the housing and a new bulb put in its place.

I need detailed information on how to replace a starter for a 2000 dodge intrepid

There's a gasket between the thermostat and the block that you need to replace.

Open the hood and you will see two T15 screws on each side of the headlight lens (bulb housing) which act as the hinges remove the two screws, pull the bulb housing out and unplug the bulb. replace new bulb houseing in reverse.

The 1994 Dodge Intrepid O2 sensor is located on the outside of the air cleaner housing. The sensor is on the back side of the housing.

The 2004 Dodge Intrepid oxygen sensor can be found on the back of the air cleaner housing. Remove the wiring harness. Remove the oxygen sensor retaining screws. Reverse the process to install the new oxygen sensor.

how to replace a map sensor on a 2004 dodge intrepid.

how do you remove the flasher relay in a 2000 dodge intrepid. I got it unplugged but don't know how to remove it

Follow the top radiator hose to the engine. It goes to the thermostat housing. Remove the 2 bolts in the housing and the thermostat is right below it.

The thermostat on a 2.7L Dodge Intrepid is under the housing where the lower radiator hose attaches to the engine.

Located in the fuel tank- may have to remove if there is not an access panel in trunk area

O,YEA AND I FORGOT TO MENTION IT IS A 1993 DODGE INTREPID...

It is at the end of the lower radiator hose on the motor. You will have to empty the radiator and remove the housing to replace it.

You need to remove passenger tire and take out the plastic door in frt of wheel well. You then will have access to battery and connections

how do you replace a dipstick tube on a 96 dodge intrepid

Remove the radiator cover the connects to the frame. These are connected by 4 bolts.Unplug the radiator fan.Remove the top two clips that hold the radiator to the fan.Remove the bolts on the sides of the fan.An instructional video explaining how to remove a radiator fan from a 93-97 Dodge Intrepid has been included below.

It is very easy to change the license plate bulb in a 2001 Dodge Intrepid. You will need to remove the tag and then unscrew the light cover. After the cover is off, unscrew the light and replace with a new one.

It is not where the housing is. You have to lift car and its behind alternater.. not easy but possible

It is under the housing that the lower radiator hose hooks to.

On the passenger side bell housing on the near the transmission.

Under the housing where the lower radiator hose hooks to the engine.

Remove the tilt steering lever.Remove the steering column cover.Unplug the wire going to the switch.Now you can remove the bolts that hold the switch to the column.An instructional video of how to remove the multifunction switch on a 1993-1997 Dodge Intrepid has been included below.

Dodge Intrepid was created in 1993.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.