Chevy Silverado
Locks and Latches
Ford Bronco Eddie Bauer

How do you remove the door lock solenoid on a 1991 Bronco?

181920

Top Answer
User Avatar
Wiki User
2008-04-25 02:42:06
2008-04-25 02:42:06

First, remove the door panel. You have to unplug the switches and the door handle. Once the door panel is removed, plug the switch for the window and roll it back up. If you look at the part of the door that faces the rear, you'll see what looks like a rivet close to the bottom. It's about the size of a dime and has what looks like a hole in the center. I had to center punch mine first to remove the center if the peice left over once installed. After it's removed, if it's there, drill the rivet. That's what holds the door lock solenoid. Once it's loose, unplug it and take it out. Be careful, some of the window track parts and door itself have some sharp edges. I didn't replace mine because I didn't want electric lock on my door. I guess it's one of those things that I fear if I decide to go into the deep pond. :-) Hope this helps!!

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

You have to remove the door panel and it will be just under the out side door handle.

User Avatar

look on sticker on door tells u what type

User Avatar

Removing a 1991 Chevrolet Silverado door panel is pretty simple. All you will need to do is to remove the screws holding the door panel in place.

User Avatar

Remove the inner kick panel. Disconnect the wiring harness. Drive the pins out of the hinges - remove door.

User Avatar

remove the door panel, window regulator, and window track. lock solenoid should now be accessable You will have to replace the latch, the solenoid is part of the door latch.

User Avatar

check fuses........ rosdale joe Better ANSWER Door lock solenoid, it is what activates the levers to lock and unlock the door. You will need to remove door handle and interior door panel to get to it.

User Avatar

there are screws in the door handle, behind the speaker cover, door release, then pop clips from the bottom upwards

User Avatar

with the door open, there r pins where the hings r, knock those up, disconnect any wires, and tada

User Avatar

yes ,but the interior door panels are different

User Avatar

To remove the door locks on a 1991 S10, the door panel has to be removed. There are bolts inside that hold the lock mechanism in place.

User Avatar

You will need to remove the door panels, and look up in the door at the handle you will see two nuts that hold the handle and a plastic clip on a rod, remove those and replace handle.

User Avatar

remove plastic moulding around door handle and door lock. unscrew door handle and unsnap plastic anchors around lower portion of door unscrew door panel from door. lift up on panel and remove. remove plastic. unscrew motor from door , let window down and remove two screws holding window. remove motor and metal bar replace and reverse process. 1991 Nissan maxima

User Avatar

Open the glove box door and remove a cover on the left side to access.Open the glove box door and remove a cover on the left side to access.

User Avatar

First you will need to remove the door panel, after this is done you should see at least 3 little marks in the door metal, which were made by a punch. Drill a hole where these indentations are and use the appropriate tool to remove the motor.

User Avatar

If you look on the cover to the fuses, or in your owner manual, it tells you what each fuse is for.

User Avatar

There is no 1988 Ford Explorer. The vehicle went into production in 1990 for the 1991 model year, replacing the two door Bronco II;. As for the Bronco II, there isn't an OBD port.

User Avatar

The 1991 Chevrolet Corvette convertible passenger side door panel is held in place with two retaining bolts and eight retaining clips. Remove the retaining bolts and pry outward on each retaining clip.

User Avatar

there are six bolts o the door you have to take off, before that you have to take the door skin off of the door ( all you have to do is pry it off for the most part, only one screw near the handle), unplug all of the wires then pull the door off

User Avatar

It could be the temperature blend door actuator.

User Avatar

Remove the inside door panel of your 1987 Chevy. Remove the linkage from the door handle. Remove the door handle retaining bolts. The door handle will come off.

User Avatar

Remove the inside door panel. Remove the door handle linkage. Remove the door handle retaining bolts. The front door handle will come off.

User Avatar

Unfortunately, you have to remove the door panel cover. There are three or four screws and several pop-clips, but it is actually pretty simple. To remove the door panel, you have to disconnect the power connector and the speaker (just clips). Hope that helps

User Avatar

i have a 1991 jeep laredo 2 door.like to find a new door for drivers side...does the 4 doors have the same size...and what years if so.....thank you Vince vcal37@yahoo.com


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.