There are 3 screws to remove. One is behind the door handle (the latch you pull to open the door from the inside), one is in the part of the door you pull to close the door, and the other is up near the side mirror (if looking at the interior of the door, it will be the upper right on the driver's door). These three screws are covered by removable tabs that are the same color as your interior. Once you remove the screws, you will need to go around the perimeter of the panel and pop it off (there are many plastic tabs). I use a flat head screwdriver to get underneathe it and start working my way around. (I've had to replace the driver's side lock twice and recently replaced the front 6" speakers).
If you want to totally remove the panel, you will need to remove the door handle latches between the panel and the door. There are two metal "arms" with white plastic connectors on the ends. One arm goes to the door handle on the outside of the door and one goes to the handle on the inside of the door. This was rather difficult since it was hard to get your hands in there. Good luck.
how do you remove the door panel on a 2001 dodge stratus?--2 door
how to remove a door lock cylinder on 2000 dodge neon
Go to this website. It will show how to remove the door panel.
To remove the sliding door panel on a Dodge Grand Caravan begin by removing the top plastic panel. Then remove the bottom piece after unscrewing a few screws located on the bottom half of the vans door panel.
Remove the 1992 Dodge Dakota inside door panel. The door handle mechanism will be visible. Remove the door handle linkage. Remove the door handle retaining bolts.
remove door panel then remove screws behind mirror. remove door panel then remove screws behind mirror.
Remove the screw under the door latch
Using a screw driver, remove the screws and remove the clips from the door panel. Remove the panel slowly, remove any wire connections, and pull the panel off the door frame.
i believe 3 screws on the bottom of panel, pop square tab in door handle compartment with flathead, unscrew, and another under ashtray dish, gently lift panel out
You will need to remove the screws in the door. They are located in the door handle, the door latch and at the very bottom of the panel. Once you remove the three screws pull the panel and it will pop out.
Using a screw driver, remove all of the screws and the clips from the panel of the car. Pull the panel away gently, remove any wire connectors, and then pull the panel off the door.
To remove and install a door mirror on a 2000 Mitsubishi Mirage, the door panel needs to be removed on the inside of the door. First remove any light lenses in the door, then unfasten the clips holding the door panel on. Then remove the mounting bolt for the mirror. Put in a new mirror, replace the door panel and the light lenses.
Remove the door bezel.Remove the window switch.Remove the door pull trim bezel.Remove the 2 7MM bolts behind the door pull trim bezel.Using a door panel tool, you should be able to remove the plastic clips behind the door panel.
Which speakers and which moulding exactly are you refering to? If you are talking about the door speakers: Just remove the screws on the panel and inside of the door handle and inside of the armrest on the door there is a screw. Then you must remove the door handle by using a screwdriver to pry off the clip behind the door handle. After that just pop the panel off.
just remove it
There are 10 Phillips screws holding the door panel on. First you would need to remove those. Then you can remove the door panel from the door. On the backside of the door panel you would need to remove the plugs from the backside of the switches. Then you can remove the screws that hold the switch into place on the door panel.
First remove the speaker grillNext remove all of the Phillips head screws from the speaker area,door pull,inside door handle and also door panel.The door panel should now be easy to remove.Disconnect any latching rods and wires from the backside of the door panel.
You have to remove all of the Phillips screws,the door handle and the master power window switches. Then tug up on the door panel and it will life right off.
Remove the inside door panel from your 1996 Dodge Avenger. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install your new door handle.
Remove the rear door panel.
You need a flat-head screwdriver and a TORX bit to remove the door panel on a 2000 Corvette. Use the screwdriver to remove the rectangular panel behind the interior door pull. Next, remove the two TORX screws. Pull the interior door handle open and use the small slots to pry off the panel. Lastly, use the screwdriver to disengage the bottom clip and pull the door panel off.
Using a screwdriver, remove the screws from the panel, remove the clips from the panel, and pull the panel away gently. Remove any wiring connectors, and remove the panel from the frame.