Not easy. TAke the door and window handles off then all screws you can find. Then the retainers on the sides and bottom of the door,pull out on the bottom and push in on the top and raise up on hte panel to diaengage from the door.
Go to the following website. It will show how to remove the door panel and the side mirror. kwmuth.com
remove your door panel remove the rubbers grommets, remove 3 10mm nuts unplug if power, reverse process
unbolt the door panel for rear, or loosen clips on front doors. then pop off and there ya go
Try searching removing the door panels. This question has already been answered a couple of times in this forum. If you have any experience at all removing door panels you should be able to figure it out. The bottom on these panels pulls out and then it lifts up, make sure you remove all the screws!!
disconnect neg bat terminal , remove belt , remove cables from alt. , remove bolts holding alt.
If this is affecting both mirrors, then the switch is likely bad. There may be a problem with the drive mechanism. Remove and disassemble the mirror to locate the problem.
How do you replace the heater core on a jimmy?
He helped with the solar panels
The solar panels were installed during the Presidency of Jimmy Carter. Ronald Reagan was quoted as saying the solar panels were "were unsightly and unnecessary." The solar panels, which were for heating water, were removed and placed on a college (Unity College in Maine) where they remained in service for another 12 years. (This answer is based on sources that referenced the removing of the solar panels at the time of removal in 1986)
you have to remove door panel and there are three nuts you have to take off of the mirror.
You will need to remove the inside door panel of your 1999 GMC Jimmy. Remove the power mirror wiring harness. Remove the power mirror retaining bolts. Reverse the process to install the new power mirror.
There are two 7mm or 8mm bolts that under the grab handle that need to be removed. There is also a phillip head screw that is behind door handle that needs to be removed. If you have power windows and door locks, pull that panel from the front and it will come off and disconnect the plugs. Pull at the bottom of the door panel and lift up and it will come off. The only thing that is holding it on after the bolts and screw are removed are clips.
answer: i just did it today 4/10/08 you have to remove about 10 screws you need a torque wrench set and a 7mm. socket . remove or just loosen up the 2 or 3 bottom panels underneath the steering column the signal relay and hazard relay are right next to each other next to the cigarette lighter housing but behind the panels that you have to remove . i pulled it out with a needle nose plyers. not bad it took me 30 min. or less the relay was $10 at the dealer . i hope this helped you...
remove serpentine belt center bolt in idler remove, and install new pulleyand rplace belt the way it came off
remove the 2 bolts that hold the thermostat housing to the intake manifold which the upper radiator hose attaches to the housing then just pull the thermostat out and replace.
I need to know how to replace a heater core in a 1992 GMC Jimmy?
take off door panel, remove window, remove window sash, unlatch the lock, take the catch pin off, slide out.
Begin by draining the water from your 1999 GMC Jimmy cooling system. Next, remove the belt from your water pump. Third, remove the water return hose. Last, remove the water pump retaining bolts. Reverse the process to install your new water pump.
Should be "peel off" type Remove wheels Remove caliper mounting bolts Slide caliper off rotor Slide rotor off hub
Remove the vacuum hose from the O2 sensor. Remove the wiring harness. Remove the O2 sensor retaining screws. Reverse the process to install the new O2 sensor.
How to remove a bad radiator from a 1992 GMC jimmy 4x44-door,v6 engine?....Thank you :)
These solar panels were a system for heating water with heat from the sun. They were taken down for repair and maintenance and never put back up. Apparently Reagan did not order them to be put back up, but I am not sure that he was consulted. Such systems were not efficient in 1985 as they are today,
Remove the plastic cover on the tailgate. There are screws in the top and sides. After that you should have access to the area where you see the lock. You will have to pull a pin to remove the lock and it should fall right out.
If it is 4x4, you have to replace the whole hub
You'll have to take the dash loos and all the electrical wireing then remove the dash from the vehicle. From there you'll have a brace over the block holding the heater core in place. Remove the brace and screws from the top cover, slide the core out and replace in reverse steps.