(1) Wind down the window glass. (2) Bend one piece of stiff steel wire into the form of a small hook like the letter L with the lower portion only about 8 mm long. (3) Unscrew and remove the lock. (4) Use a electric light bulb of at least 60 W and look into the locking mechanism from above the two trims. (5) There is one piece of steel button hanging from the locking mechanism. You insert the steel hook and turn it 90 degree so that it can engage with the steel button of the locking mechanism. (6) Pull the button up and the lock will be released. This is not that difficult. (7) If you cannot locate the steel button, you should try to remove the fabric of the other door and locate the release button so that you know where to look for the release button.
How do you remove the driver side door panel of a 1998 VW Beetle to replace the door handle cable?
You will need a torx head screw driver and a Phillips screw driver, remove the screws around the closing handle and the opening handle, then gently pry at the bottom of the panel to pop the fasteners loose working your way up the sides, lift the panel out of the the window slot and over the door opening handle.
Remove the screws from the handle and then the door panel will slide up. It has clips that will only let it slide up
One screw near the handle three under the pull handle then pry with screw driver or interior panel remover.
remove small round plastic cap behind inside door handle, remove the screw, remove screws from door panel edges, starting at the bottom..pull the panel straight off the door. a door trim tool (if available) may be used to release the clips behind the panel
Using a screw driver, remove the screws and the clips in the panel of the door and remove the panel gently. Remove any wiring connectors between the panel and the door, then remove the panel the rest of the way.
remove the inside door panel and go from there.
There is a little plastic pin that holds the handle on. Press the pin out and slide the handle sideways to remove. Replacement is reversed.
To remove the inside door panel of the Ford F250, first open the door and remove the screws for the door handle. Then, pry the door skin off of the inside starting at the bottom of the door.
Remove the inner door panel & start checking for linkage & handle problems
remove the screws that are around the side and bottom of panel. remove covers located by mirror and by the door hinge. remove the screws you found use a small bent screw driver and put it in the hole on the underside of the the close handle to push the cover off the handle. remove these two screws remove the screw behind the door open handle. pop off the cover that is over the mirror mechinism. now pull up on the panel and voila!
After unscrewing all the screws on the perimeter of panel you must slide the interior door handle mechanism to release the panel.
very easy to remove first remove screws _ two from each side then two from bottom then remove small black cap inside interior handle (opener) then using t15 driver remove screw - carefully remove black surround from interior door handle. then using t20 driver remove two screws from interior door pull. door panel should now pull off but be sure to remove plugs from small speaker and and elec window switch then panel can be taken away completely.
find yourself the correct bit for your drill or driver and go along the outer edge of the door panel and you will find the first screws to remove, then you have to remove the plastic cover on the armrest handle where you will find another screw and you will also have to remove the black plastic piece that houses the door handle.
remove the window handle, remove screws from armrest, remove the inner door handle and the screw on the lower rear of the door panel, lift the panel upwards to remove from the slots along the bottom of the door.
You can't remove just the inside handle. The handle is part of the door panel.
Using a screw driver, remove the screws in the door panel, unclip any of the clips on the door panel holding it to the frame. Gently pull the panel away from the frame, remove any wire connectors and pull the panel to release it from the frame completely.
Remove door panel for access and investigation
Use a screw driver, remove the screws in the panel and remove the clips in the panel. Pull the panel out gently, remove any wire connections, and remove the panel completely.
take off door panel by removing screws, push in on middle of holders ,lift panel off of door release clips on door lock and door handle rod remove handle.
Remove the driver of it in the the Control Panel-Devices And Printer-Right Click On the REMOVE DRIVER From iT Your Problem Is Solved
Remove the inside door panel of your 1987 Chevy. Remove the linkage from the door handle. Remove the door handle retaining bolts. The door handle will come off.
Remove the inside door panel. Remove the door handle linkage. Remove the door handle retaining bolts. The front door handle will come off.
Door Panels Removal & Installation 1. Remove the sail panel. 2. Remove the door panel by carefully lifting the panel upward to release the retaining clips. 3. Remove the electrical plugs that control the windows, exc. 4. The installation is the reverse of the removal.
Remove the two vertical Phillips head screws in the grab handle. Remove the window handle if equipped. Remove/ unplug the electric mirror/ window switches if equipped. Grab the doors at the bottom and pull hard. Then work you way around the left and right side of the door panel pulling on the panel. There are some white plastic push pins on the back of the panel that hold it to the door. When all of the pins are loose, lift the panel upwards and remove it. This is a less than 5 minute job.