Chevy Blazer
Ford Expedition Eddie Bauer
Ford Expedition XLT
Ford Ranger XLT

How do you remove the drivers side door to a 1997 Blazer?

363738

Top Answer
User Avatar
Wiki User
2015-07-15 21:21:42
2015-07-15 21:21:42

After you've removed the door trim panel and unplugged all electrical connections from the door: 1 - open the door all the way and support it on jacks or blacks covered with cloth or pads to prevent damaging the paint.

2 - Use a spring compressor tool, available at most auto parts stores, to compress and remove the hinge spring. WARNING: The door hinge may fly off the compressor tool during removal. To prevent personal injury, cover the spring with a heavy rag before removing it.

3 - Have someone hold the door, remove the hinge pin retainers and drive out the pins then carefully lift off the door.

4 - If the door doesn't close properly after installation, the door latch striker can be adjusted both up and down and sideways to provide positive engagement with the latch mechanism. This is done by loosening the door strike bolt and moving the strikeer as necessary.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

on a 1997 blazer, how to remove drivers side mirror under your handle to close the door is two 7mm bolt and behind your handle to open the door is a Philips screw and that plate behind it comes off then CAREFULLY remove the door panel trust me you don't want to break the plastic then you will see your mirror bolts and electrical wiring

User Avatar

The 2001 Chevy S 10 Blazer power door lock relay switch is located inside of the drivers side door. You will need to remove the drivers side door panel in order to access the door lock relay switch.

User Avatar

To remove the drivers side window and regulator, you will need to remove the door panel from the door. Then you can unbolt the regulator and window to remove them.

User Avatar

Take the door panel off and there are bolts inside.

User Avatar

I have a 1997 Chevy Blazer 4DR and the relay is located underneath the glove box.

User Avatar

a 4 door 97 blazer front how do i do it

User Avatar

You will need to remove the inside door panel of your 1988 Chevrolet Blazer S 10. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.

User Avatar

You will need to remove the inside door panel of your 1993 Chevrolet Blazer. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.

User Avatar

;how to remove drivers door panel to repair door restrictor

User Avatar

its on the drivers side dash board. to get to it you have to have the door open and give a half a turn and the panel should come right off

User Avatar

The 1998 Chevrolet Blazer door panel is held in place by eight retaining clips. Pry outward on each retaining clip to remove the door panel.

User Avatar

Remove the inner kick panel. Disconnect the wiring harness. Drive the pins out of the hinges - remove door.

User Avatar

Vehicle rated weight is on a tag on the drivers door or door jam

User Avatar

how do remove driver door on Chevrolet aavalnche

User Avatar

It is located on drivers side dash board. It is visible when you open the drivers door.

User Avatar

on the drivers side of the dash, between door panel and dash under a panel you remove with a flathead

User Avatar

i think you should remove the door first then remove the door panel by hitting it with a soft hammer to release it.

User Avatar

The one inside the drivers door. It will be on the side of the dashboard. A square door

User Avatar

look at the info sticker inside drivers door. My 89 blazer came with 31x10.5x15 from the factory.

User Avatar

If the door is open. or any door is open. All doors will lock but the drivers door. I guess so you don't leave keys in. That's how it works on my 99.

User Avatar

Listed on the driver's door post.

User Avatar

Remove the speaker covers from your 1997 Mercury. Remove the door speaker retaining screws. Remove the door speaker wiring harness. Reverse the process to install your new door speakers.

User Avatar

You will need to remove the rear door speaker covers. The Chevrolet blazer speaker covers are held in place with two retaining screws. Remove the speaker retaining screws. Remove the speaker wiring harness.

User Avatar

check under the frame rail onthe drivers side at the drivers door thats where its at on a 1999


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.