Auto Parts and Repairs
Jeep Grand Cherokee Limited
Oldsmobile Achieva
Chevy Camaro Z28

How do you remove the electrical plug from the oil level sensor on a 1993 3.3 Olds Achieva?

282930

Top Answer
User Avatar
Wiki User
2015-07-15 19:09:25
2015-07-15 19:09:25

Squeeze the locks on the sides of the plug.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

It is not an oil level sensor it is an oil pressure sensor. It just unscrews.

User Avatar

The coolant sensor is located approx. 1/2 way down the radiator on the passenger side of the vehicle. Disconnect the electrical connector, Remove the spring clip, pull out the sensor, replace with new sensor, replace the spring clip, connect electrical connector.

User Avatar

It is in the passenger side coolant tank on the radiator. If the light is on and the coolant is at the proper level then the sensor is defective. To replace it you will have to drain the radiator. Disconnect the wire and remove the clip and remove the sensor.

User Avatar

Remove brace to better access the coolant area. Unplug and remove the battery. Remove the electrical connector from the sensor. Have container beneath vehicle to catch any coolant. Remove the wire, or wires, that are holding the senor in place. Add antifreeze to the O rings and push the new sensor into place. Replace the battery and brace cover.

User Avatar

Empty gas tank, remove tank straps, lower tank, disconnect hoses and electrical connectors, rotate lock ring, lift unit out

User Avatar

To change the fuel level sensor in a 2000 Chevy Impala, first close the gas and power lines. Remove the wiring and then drop the car tank. Remove the old fuel level sensor and replace it with the new one.

User Avatar

The coolant level switch on a 95 Achieva has a sticking problem. If you tap the coolant tank near the sensor the light will go out

User Avatar

You have to remove the fuel tank. The sending unit is at the top of the fuel tank. Once you have done that remove the fuel lines and the electrical connector that hooks to the sending unit and remove it for the tank. All of this can be a pain if you have never done it before and if there is alot of fuel in it.

User Avatar

Answerthe sensor is located about 4 inches down inside of the radiator....probably need to replace radiator. Wrong.. that is the level sensor, and it can be replaced by itself by removing the clip around the sensor and pulled out, however it will leak coolant if the radiator is full so be careful. the temprature sensor is on the block by the the thermostat housing. follow the upper radiator hose to the engine and your hand will hit the temp. sensor. it has electrical wires on it, disconnect them and remove the sensor with the correct wrench. replace the sensor and reinstall the electrical clip, the sensor is around 13 dollars

User Avatar

If the coolant system (radiator and reservoir) is full and the light remains on, the probe on the coolant level sensor is probably dirty. Remove it from the radiator, clean it gently with brake clean and an old toothbrush, re-install it, refill coolant system and you should be good to go.

User Avatar

remove the two 10mm nuts. dissconnnect the coolant level sensor plug and remove coolant hose's

User Avatar

The coolant level sensor is about three inches below the coolant cap on the back side of the radiator. It is a 1.5 X 1.5 inch box with an electrical plug going into the bottom of it.

User Avatar

Not a major job Disconnect brake lines Disconnect electrical level sensor Remove mounting bolts BENCH BLEED NEW MASTER CYLINDER PRIOR TO INSTALLATION

User Avatar

Yes you can, however you will forever get a check oil level alert on the info-center computer.

User Avatar

On the 2002 grand prix there is a sensor in the radiator about 6 inches from the top on the vehicles right side. It works based on electrical conductivity of the coolant. when it becomes dirty (doesn't conduct) or fails it will show low level. Remove the battery (for access) remove a spring clip (holds the sensor in) pull out the sensor and clean or replace. for the purpose of testing, with the sensor out of the radiator, but still plugged in and the key in run (engine off) ground the sensor to the battery. if the dash light goes out, the sensor is good. clean and reinstall.

User Avatar

The coolant level sensor is located in the coolant reservoir tank. It should just screw or press in. Unplug it, remove it and put a new one in.

User Avatar

Empty and remove the fuel tank. It is inside the tank mounted with the level sensor. (remove it from the top)

User Avatar

Coolant level low or level sensor malfunction.Coolant level low or level sensor malfunction.

User Avatar

Sensors are transducers basically convert non electrical quantity to electrical quantity. Sensor may be classified as Piezoelectric sensors Thermoelectric Sensors Capacitive Sensors Inductive Sensors etc. Sensor can not produce adequate level of power so they can directly fed to amplifier hence need a processing amplifier.

User Avatar

Its inside the coolant overflow tank/reservoir (its the plastic reservoir where you pour in your coolant). Look on the side (the side that faces the engine) and you'll see an electrical wire is connected by a harness. That's your coolant level sensor.

User Avatar

Check the fuel level sensor. It's in the tank, attached to the fuel sending module. If you need to replace it, you'll have to drop the gas tank, carefully remove the retaining ring around the fuel sender, and pull the whole unit out. You can then remove the level sensor from it.

User Avatar

On the passenger side of the engine compartment there is a surge tank remove that and the sensor is in the bottom. It will be the clear plastic tank where you add Coolant.

User Avatar

there is no such sensor in pokemon.

User Avatar

The oil level sensor for the engine is generally located in the oil pan.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.