On the left and right sides of the radio there are four rubber tabs, remove these with a pocket knife or small flathead screwdriver, they will pop out with little force.
After you remove the rubber tabs, there are four holes. Take a wire coat hanger and cut off the two ends making a "U" shape. Place the ends of the U-shaped hangers into the holes. Behind the holes are spring clips that hold the radio in place. Push the hangers in about 1/4 to 1/2 inch so that it will depress the spring clips on each side. Apply a little outward pressure and pull gently this should release the spring clips from their position and you should be able to pull out the radio.
You then unhook the antenna wire, two wiring harnesses, and the ground wire from the rear of the radio. That's it. :)
If anyone has the color code information I would be grateful if you could post them. I have only found conflicting information on the net so far.
view website www.cdplayerrepair.com/remtips/vigor_rem.htm
you will notice small holes at each corner of the stereo face, you just need top poke something into all 4 holes to release the unit
You can use the 1990 stereo in your 1992 Accord, but the 1998 will not bolt in the correct way.
MAYBE WAL-MART IF NOT A STEREO INSTALL SHOP
Found this on another FAQ site: http://www.installdr.com/InstallDocs/Toyota/PDF/869005.pdf complete removal and install of a new deck....
That should be the factory amp for your car stereo
u have to go to the shop and buy it and pay the shop to install it
yes, you will have to remove all the plastics from the 94 and put them into the 92, as well as the wiring.
ITs Behind Your stereo its sitting flat its only 2 screws To remove but you need to remove The carpet From The sides And you Will see it !
Were is the egr on a 1992 mazda protege
Will a 1992 mazda miata hardtop fit a 2000 mazda miata?
The Apples in Stereo was created in 1992.
Where is the headlight relay in 1992 Mazda Protege?"
NO, but the entire wheel assembly will have to be removed.
you have to remove the whole door panel in order to gain access to the factory speakers in which should be 4x6.
The 1992 Mazda B2200 will hold close to 17 gallons of gas. The 1992 Mazda B2200 is a four-cylinder vehicle.
You will need to remove the door cards, then get to the back of the handle, should be some mounts to remove then you should be set.
Brake fluid location in 1992 Mazda mpv
You have to remove half the dashboard before you can even get access to the stereo mounting bolts. Start with removing the glove compartment, then the molding on the right side of the stereo. Ash tray, then I think you can remove the molding that is around the stereo. You can find a very helpful step-by-step guide at www.installdr.com for many types of vehicles. The guide you are looking for can be found here: http://www.installdr.com/InstallDocs/Toyota/PDF/869017.pdf Have fun!!!
The easiest answer to this question is "www.installdr.com", there is a complete .pdf including diagrams on how to install the stereo for a 1992 prelude.
You can reset the factory stereo on a 1992 Volkswagen Transporter TDI van by disconnecting the battery for several seconds. Once you plug the battery back in, the radio will ask for a code. The code is essential in order to gain access to radio functions again. The radio code can be found in the owners manual. If the manual is not available, you can obtain the radio code from a dealership.
The speaker size for a 1992 Mazda 323 would be 6-1/2.
The 1992 Mazda Miata is equipped with a non-adjustable steering wheel.
Pull out the ashtray and then the panel above and the cup holder . Radio will then come out
DONT BE STUPID