answersLogoWhite
Dodge Ram Van
Ford Vans
Ford Aerostar XL
Ford E-150 Van

How do you remove the fan cluch on a 1983 econoline van?

606162

Top Answer
User Avatar
Wiki User
2006-03-29 22:30:31
2006-03-29 22:30:31

I'm not sure if you have to remove the fan shroud, look at it, to see.Put a square stemmed screwdriver between the bolts and loosen the other one,relocate the screwdriver until all bolts are loosened then remove the bolts.Sometimes the fan is still stuck on the water pump and must be tapped off,careful,don't want to damage your radiator. L.Keedy

1

Related Questions

User Avatar

Need to know how to remove heater fan on 1999 ford e 150 van with small v6 engine

User Avatar

how do i take the fan cluch off a 89 ford ranger yo replace

User Avatar

You need to rent or buy a fan clutch removal tool kit. you need to remove the fan and clutch as one before you can separate the fan from the clutch.

User Avatar

your cluch went out on your fan or your belt broke

User Avatar

Some vans don't hav a fan clutch but electric fans. If yours does have one, simply remove the 4 bolts holding the fan on then take the bolts out of the clutch. If it has just one big nut a special tool is required.

User Avatar

Remove the fan itself then remove the clutch from the fan

User Avatar

The wench will be used to remove the clutch fan nut. Remove the nuts holding the fan then remove the fan blade.

User Avatar

When the clutch fan locks up it makes a sound like a propeller on a airplane and the more you rev the engine the louder it gets.

User Avatar

They make a special wrench to remove the fan. If you are going to replace the water pump then you can use a long chisel and hamer to strack the fan nut to loosen it up. And then spen it off. When you put it back on, tighten it by hand. Then hit it easy with hammer and chisel to tighten it a little. Do not hit it hard or you will damage the new pump. When you start the engine, It will tighten itself by the force of the engine turning the fan. TRUST ME.

User Avatar

located and connected to the fan,drain radiator,remove both ,radiator hoses, remove fan belt,remove fan shroud,remove radiator.remove fan,remove water pump.

User Avatar

How do you remove the fan shroud on a 2004 get envoy

User Avatar

Remove the wiring harness or the fan motor belt, depending on the year of your Chevy Cavalier. Remove the fan motor retaining bolts. The fan motor will come off.

User Avatar

The fan does not have a switch - the thermostat switch runs the fan.

User Avatar

To remove the fan clutch on a Chevy Tahoe, the upper fan shroud must first be removed. Once removed, a tool is needed to hold the clutch in place to allow for the fan to be removed. The nuts must be unscrewed on the fan in a counterclockwise rotation. Remove the nuts on all side and the fan clutch will remove.

User Avatar

Buffalo Bill - 1983 The Fan 1-11 was released on: USA: 17 August 1983

User Avatar

how do you remove a fan blade from a 1998 ford explorer

User Avatar

Remove the wiring harness to the heater blower fan. Remove the retaining bolts. Remove the fan from the blower. Reverse the process to install the new heater blower fan.

User Avatar

You will probably have to remove fan/pulley first to get clearance then just remove fasteners from rad.

User Avatar

Remove the radiator cover the connects to the frame. These are connected by 4 bolts.Unplug the radiator fan.Remove the top two clips that hold the radiator to the fan.Remove the bolts on the sides of the fan.An instructional video explaining how to remove a radiator fan from a 93-97 Dodge Intrepid has been included below.

User Avatar

Well, I looked for this information all over the internet today and finally broke down and bought a Chilton's manual. It says to locate the heater fan assembly just below the dash on the passenger side and there will be a section that just houses the fan itself. That is what you must remove. You will unplug the fan (2 connectors at the top of the assembly), then remove screws that surround the fan assembly, disconnect the rod from the heat mixture lever (near kick panel on right), and remove the assembly. Then you need to open the hood and remove the 2 heater hoses (there will be leakage if you don't drain the antifreeze first). Go back in the cab and pull the heater core free.

User Avatar

remove your fan shroud then losen the tensioner and remove your belt.

User Avatar

Remove the bolts, remove offending fan and replace with new one

User Avatar

# Disconnect negative battery cable # Remove the serpentine drivebelt # Remove the coolant reservoir from the fan shroud and set it aside without draing the tank or disconnecting the hose # Disconnect the electrical connectors at the windshield washer reservoir and remove the reservoir from the fan shroud # Remove the fan shroud mounting bolts # A special 36mm fan wrench is required to remove the cooling fan can get at most auto parts stores

User Avatar

You need to remove the upper hose and then the fan shroud on the upper half. The fan clutch is then held on with 4 bolts. Remove these and the fan will slide out from the engine. You might need to loosen the belt so you can turn the fan and get to all 4 bolts. With the unit removed you can then remove and replace the fan on the clutch assy. Reinstall in the reverse order.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.