On an 88 Colt along with most cars u have to remove the tire. Then there should be a cap with a clip that holds it on remove the clip then the cap will come off. There will be a bolt that u will have to remove. After all this take off the calipers. There should be two bolts that hold them together. Once the calipers are off remove the plate. (If applicable) There might be one more bolt that holds the disc to the axle. Then the discs should slide right off.
remove rear wheel, remove brakes and cylinder is held on by 2 bolts from back of plate. remove bolts and brake line from cylinder !! somtimes you can take top nails holding brakes out to allow room to remove cylinder.
First you have to jack the car up after loosening your lug nuts and then you remove the wheel. After you do this, you have to pull the brake drum off. Next, dis assemble the brakes then disconnect the brake line from the wheel cylinder. Then you remove the two bolts holding the wheel cylinder on and put the new one in. Re install the bolts, and brake line, put the brakes back on, put the drum back on and bleed the brakes. Put your wheel back on and drive away.
Remove the tire and wheel from your 1994 Plymouth Sundance. Remove the brake assembly spring. The brake pads will come off. Reverse the process to install the new brakes.
Work inward in a circular motion.
Replacving a master cylinder is usually pretty straight forward. Remove the brake lines, unbolt/remove the master cylinder, Re-install in reverse order. The hard part is bleeding the new master cylinder/brakes once you put it on. Caution: Your life depends on your brakes. If you're not sure you can do it right... don't. Get someone to help you.
If you are talking about the brake master, then remove this as a complete unit, and replace it as a complete unit. You do want your brakes to work the next time you need them...............
remove the rear brakes, then remove the brake line to cylinder. remove the bolt holding cylinder on. then pull out wheel cylinder. to install cylinder, position it in place, put bolt back in cylinder to hold it. hook back up the brake line then put the brake shoes back on. when done bleed the system if need be.
ok if you can you can open the bleeder valve on the cylinder and carefully pry the cylinder back into the callipar. you will have to bleed your brakes afterwards.
You have to drain/remove the "transmission" oil pan to get access to the filter.
I'm pretty sure that takes a 7mm Allen key.
Squealing brakes in a sign of worn out brake pads or shoes. Can also be leaking wheel cylinder. Suggestion: Remove the rear wheels and find out what is going on. defective brakes is a safety hazard.
It is much easier to reach them if you remove the air filter box itself. They are basically opposite the front ones.
how to remove back brakes on a 2002 Chevy surban
Air in system? Remove and bench bleed master cylinder Bleed lines and calipers
I guess you're referring to the wheel cylinder brake backing plate at the wheel. The one which operates the rods that move the brake shoes. It's usually pretty obvious. A couple of bolts to remove and a brake line to remove from the cylinder. Bear in mind that you'll have to fill and bleed the brake lines after replacing the cylinder.
The Master cylinder is under the drivers side floor mat. You need to remove the metal plate to get at it.
It's usually caused by a leak in your wheel cylinder. The part itself is around $10.00, but be careful when you remove the brake line, it is very easy to break. It could also be: the rear brakes were wrongly made by the manufacture and so were the specs dispersed to all other companies to it warps horribly the wheel cylinder master cylinder.
unplug electrical connector for the fluid level warning switch. remove as much fluid as possible from master cylinder, with a syringe or similar to suck out the fluid. take off the brake lines to the cylinder. pull lines away from cylinder, and cap the ends so you do not loose fluid from the lines. remove the nuts attaching master cylinder to firewall. pull the cylinder off of the studs to remove it. bench bleed the new cylinder before installing it. (that means to remove all air trapped in cylinder). fill up new cylinder with new fluid, and push on plunger of cylinder to release the air. do this until no more air bubbles are presant in cylinder. if no fluid is lost from the lines and all the air is out of the cylinder. there is no need to bleed all the brakes just bleed by remove lines at cylinder if needed. GOOD_DAY!
how do you remove a power steering pump from a 1995 plymouth voyager?
Remove the 2 screws holding the plastic housing around the steering wheel. Remove the top part of the housing; pull down the bottom part as it does NOT come off. Set your ignition to the RUN position. Push in the tab on the underside of the lock cylinder and pull out the old cylinder. Get your new cylinder & set it to the RUN position (or at least out of the LOCK position). Slide your new cylinder in the way the old one came out. Make sure it locks in correctly.
To remove brake cylinder from Corsa B, first disconnect and unplug hydraulic lines. Remove the nuts and the master cylinder. Remove the reservoir cover, followed by the brake cylinder.
Remove wheel if disc brakes: Remove caliper mounting bolts and slide caliper out of the way. If drum brakes: remove brake drum Remove brake line Hub assembly should be secured by 4 bolts You may have to separate backing plate from hub assembly, by supporting backing plate and striking hub assembly sharply w/hammer
How do you remove the rear drum brakes on a 1998 ford escort
If you are new to doing drum brakes, then remove the drums on both rears and do one side while looking at the other side for reference.
how remove cylinder head