answersLogoWhite

0


Best Answer

I haven't done that exact model, but most fords you need the key (stupid I Know)put the key in and turn, there is a button sticking through the column push it in with the key turned should pop out! hope that helped?

User Avatar

Wiki User

โˆ™ 2006-04-01 23:54:40
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove the ignition key cylinder in a 1989 ford bronco II?
Write your answer...
Submit
Related questions

How do you remove the ignition switch on a 1989 Chevy Corvette?

Remove the retaining ring from the top of your 1989 Chevy Corvette ignition switch. Slide the ignition switch out and remove the wiring harness.


Can you take oil pan off 1989 bronco without removing the engine from the vehicle?

how to remove oil pan from 1989 bronco 2


How do you change the ignition lock cylinder in a 1989 Chevy Cheyenne when there is a key broke off in the ignition and it won't turn?

A locksmith may be able to remove the broke key and make a new one. Or just replace the ignition.


How do you remove an ignition lock on 1989 GMC Sierra?

== ==


How do you change the ignition switch on a 1989 Chevy Blazer S10?

You will need to remove the retaining ring from the top of your 1989 Chevrolet blazer ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.


How do you replace an ignition switch on an 1989 camaro?

switch itself or key cylinder?


Ignition diagram for 1989 Mazda b2200 truck?

witch is the 6th cylinder


How do you remove the window in the rear hatch of a 1989 ford bronco?

To remove the window in the rear hatch of a 1989 Ford Bronco, the weather stripping around the window will have to be pulled back or pushed down slightly. This can be accomplished with a straight screwdriver or a putty knife.


How do you locate the ignition switch on a ford Bronco II 1989?

If you know where to put the key in, you know where the ignition switch is... Actually, safe to say you should stay away from it.


How do you replace a 1989 Mercedes Benz 300sel ignition?

Retaining ring from the top of your 1989 Mercedes-Benz ignition switch. Slide the ignition switch out. Remove the wiring harness. Reverse the process to install your new ignition switch.


Where is number one cylinder on a 1989 Ford Bronco 29 V6?

passenger side front cylinder is 1. left side is 123 driver side is 456


How can i replace an ignition switch in a 1989 Oldsmobile cutlas ciera sl?

Remove the retaining ring from the top of the ignition switch. Pull the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.


Diagram of a 1989 Bronco II Fuse Box?

list of fuses for 1989 bronco 2


How do you remove and replace the ignition coil on a 1989 Toyota Celica?

you suck it up


How do you replace 1989 jeep Comanche clutch slave cylinder?

Remove the transmission to excess the inturnal slave cylinder


1989 Ford Bronco RABS computer location?

Quote from Chilton book: " The module is located on the firewall just inboard of the master cylinder."


Trying to find key in ignition buzzer location in a 1989 Chevy Blazer?

The buzzer that lets you know the key is in the ignition in a 1989 Chevy Blazer is in the steering column. To access it you would need to remove the steering wheel with a special tool, or remove the ignition assembly. The key makes contact with a tab that activates the buzzer.


How do you replace starter on a full size 1989 Ford Bronco?

remove batt. cable from starter(its not wired to batt so has no power) remove 2 1/2 bolts remove starter


How do you remove the turn signal arm on a 1989 Ford Bronco?

It unscrews by turning counterclockwise. There is a small "flat" on the shaft to assist in removal.


How do you replace brake light on 1989 full size bronco?

Well you take out the tail light assem and remove the blown bulb


What is the fuel pump wiring diagram for a 1989 ford bronco 11?

A wiring diagram of a 1989 Bronco 11 fuel pump can be purchased from most auto parts stores. It can also be found in do-it-yourself repair books for a 1989 Bronco 11.


Will the auto trans from 1986 302 bronco work in a 1989 351 bronco?

it shold


Will a 1984 ford bronco back window fit a 1989 ford bronco?

yes


How do you replace the ignition switch in a 1989 Pontiac Le Mans?

First, I'm guessing you are referring to the ignition lock cylinder w/key. The ignition switch is plugged into the back of the cylinder lock. I just removed the cylinder lock from a '92, so this should be the same. Pull the steering wheel with adapter legs (KD3510) so you can access the release through the hole just below & to the right of the shaft (about 4 o'clock). The bottom plastic cover around the steering column needs to come off too. Put the key in & turn to position II, so that the release will depress. I used a small pick. Also, remove both the ignition switch & the cable behind the cylinder. To remove the ignition switch, back out the two set screws & pull off. Gently pry out the cylinder lock by twisting the blade of a screwdriver between the casting & the switch.


How do you set ignition timing on a 1989 ford probe?

where are timing marks on 89 ford probe 4 cylinder I have the bottom not the top

Study guides

๐Ÿ““
Create a Study Guide