answersLogoWhite

0


Best Answer

Follow the large purple wire from the ignition swiych to the neutral safety switch or the clutch switch and check the power. You may not need to replace the ignition switch.

User Avatar

Wiki User

โˆ™ 2008-12-25 21:50:23
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove the ignition switch on a 1979 Chevy Corvette you took the lead wire off the starter that comes from the switch and had meter on it while someone turn the key and read 0 volts?
Write your answer...
Submit
Related questions

How do you remove the ignition switch on a 1989 Chevy Corvette?

Remove the retaining ring from the top of your 1989 Chevy Corvette ignition switch. Slide the ignition switch out and remove the wiring harness.


How do you replace a starter 1999 corvette?

Remove the positive battery cable from your 1999 Chevrolet Corvette at battery. Remove the starter cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.


How do you replace a starter on 95 Corvette?

Remove the positive cable from your 1995 Chevy Corvette battery. Remove the cables from the front of your old starter. Remove the starter retaining bolts. Reverse the process to install the new starter.


How do you change starter on 1975 Corvette?

Remove the positive cable from your 1975 Chevrolet Corvette battery. Remove the two cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.


How do you Replace starter in 1988 Corvette?

You should begin by removing the positive cable from your 1988 Chevy Corvette battery. Remove the cables from the front of the starter. Remove the three starter retaining bolts. Reverse the process to install the new starter.


Where is the ignition module on a 93 Corvette?

Remove distributor cap it is underneath.


How do you install a starter for a 1998 cutlass?

Turn of the ignition and disconnect the negative battery charge. Remove positive cable from the starter. Loosen the bolts that hold the starter to the block and remove the supporting brackets. Remove the bolts holding the starter. Remove the starter and place a new one.


How do you remove ignition switch on 1996 Chevrolet Tahoe?

Chevy Tahoe Ignition Key Starter Switch


How do you remove ignition coil from 1985 corvette?

The coil is located in the top part of the distbutor cap


How do you remove ignition switches on 1981 corvette with t and t'?

To remove the ignition switch in a 1981 Corvette, insert the key into the ignition while leaving it in the "off" position. Insert a straightened paper clip next to the key, turn the key to the "Acc" position, pull the key and clip out together, and place the coil down.


How do you replace starter in 1996 Nissan 4WD pickup?

remove negative battery cable,jack up truck and remove front passenger tire,easier to get to,its next to oil filter,remove ignition wire from starter,remove positive battery cable from starter,remove 2 bolts holding starter on to engine,remove starter,installation is same as installing.g0ood luck.


How do you replace starter on 3.3L 1998 Dodge Grand Caravan?

Remove negative cable from battery Disconnect positive cable from starter and ignition wire Loosen mounting bolts from starter Remove starter Install new starter in reverse order of removal


Where is the starter located on a 90 Corvette conv?

I have a 90' ZR1 and the starter is under the plenum a costly job about $700 plus parts. They have to remove the top of the engine to get to it.


Starter motor spins but does not corvette engine flywheel?

You have a bad bendix spring or solenoid,either way you will have to remove the starter and replace whole or just the engagement solenoid


How do you remove a 1976 corvette ignition switch?

Ignition switch is located above brake pedal on column. It has long flat electrical connector to it. If by ignition switch you mean the key tumbler: Remove steering wheel. Remove lock plate. Remove Turn signal switch. Remove screw retaining ignition. There should be a code stamped on the ignition. If the ignition is still good a locksmith can cut the key from the code. Might be cheaper to slap a new one if you have already got that far though.


How do you diagnose a starter or ignition problem on a Nissan Altima?

Take the steering column housing off (usually held by 4 screws from the bottom) and remove the starter cap from the back of the ignition cylinder. In a Nissan, the ignition cylinder usually has a T shaped pin which turns the starter. if you can start your vehicle by turning the starter cap with a screw driver, you probably don't have an issue with the starter.


How do you change a 2000 Isuzu Rodeo starter?

remove the starter bolts your 12v power supply and ignition wire then remove exhaust bolts from manifold a few twist and turns and out she comes


Remove speedometer 1980 Corvette?

1980 corvette , how to remove speedometer


How do you remove the ignition lock on a 1973 Chevy Corvette?

To remove the igniton lock, remove the steering wheel and turn signal switch housing. From there you will be able to see the lock which holds the ignition lock into place. slide a screwdriver into the slot and apply pressure. The igntion lock can then be pulled out.


When you turn your ignition switch you hear a whining noise and engine does not turn over?

Starter solenoid is defective. You will have to remove the starter and have it tested at an auto parts store.


What does it mean when you Replace starter and when you go to connect cables to battery the starter starts and stays on without key in ignition until you remove cable from battery?

The wires to the starter are probably connected wrong.


How do you remove and to replace starter?

In general, remove negative cable from battery, remove electrical wires from starter, remove bolts holding starter in place, remove starter. Replace starter in reverse order.


How do you remove the ignition switch not lock on a 1973 Chevy Corvette?

switch should be on the bottom of the steering column ,probably have to drop the two bolts on console to get to it


How do you remove the key cylinder on a 2000 Corvette?

REMOVE THE CENTER CONSOLE TRIM FROM AROUND THE GEAR SHIFT. ONCE THAT IS OUT OF THE WAY THERE ARE TWO BOLTS THAT HOLD THE IGNITION SWITCH IN THE DASH. REMOVE THE BOLTS AND THE ELECTRICAL CONNECTOR AND YOU SHOULD HAVE IT IN YOUR HAND.


How do you replace a starter?

disconnect power from battery, remove wires connected to starter, remove bolts from starter (usually 2), remove starter.

Study guides

๐Ÿ““
Create a Study Guide