Chevy Corvette
VW Jetta
Ford Escort LX

How do you remove the ignition switch on a 1998 VW Jetta?

161718

Top Answer
User Avatar
Wiki User
Answered
2010-10-17 14:24:47
2010-10-17 14:24:47

start by removing the shroud around the column. remove the assembly that houses the ignition switch, there is a spring catch located in the lock and tumbler, you will have to drill a small hole in the side to push this spring and while pushing the spring down rotate the switch and pull out.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Begin by removing the retaining ring at the top of your 1998 BMW ignition switch. The ignition switch will slide out. Remove the wiring harness.

You will need to remove the retaining ring at the top of your 1998 Chevy Lumina ignition switch. Slide the ignition switch out. Remove the wiring harness.

key switch tumbler removal on 1998 astro

HOW DO I REPLACE 1998 camry ignition switch?

How do you remove ignition tumbler 1998 ford Mustang?

The 1998 VW Jetta drivers side power window relay switch can be found inside of the drivers side door. You will need to remove the drivers side door panel in order to access the power window relay switch.

One to repair an ignition switch on your Astro Van is buy a replacement steering column from a local salvage yard including the ignition key, and replace the whole steering column. RC Houston, TX

No, there is no kill switch except for the ignition switch.

The ignition switch is on the steering column under the dash about 18 inches from the floor.

Part of the coil mounted to the fire wall

how do I remove the key switch from a 1998 ford contour You have to remove the plastic trim around the steering column (behind the steering wheel). Put the key in the ignition cylinder and turn one click. There is a small hole on the side of the ignition cylinder, stick a small screwdriver into this hole and press hard. Pull out the ignition cylinder with the key.

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder

the wire is Yellow coming out of the ignition switch going to the Neutural safety switch, then purple from the neutual safety switch to the starter

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder

I need to replace the ignition switch on a 1998 KIA Sportage . Can this be done with a universal ignition switch ? There are 6 sets of wires going into the KIA switch. The universal switches come with 3 or 4 posts.

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder

Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disable the airbag system * Remove the tilt lever if equipped * Remove the upper and lower steering column covers Ignition Switch * Remove the ignition switch retaining screws * Detach the ignition switch from the steering column housing assembly and unplug the electrical connectors Key Lock Cylinder * Turn the key to the run postion * Depress the lock button and remove the key lock cylinder

2002 Audi quattro 1.8 ignition module location

The only Killswitch is the ignition switch. GM vehicles are not equipped with a fuel pump inertia switch.

ignition switch in the steering column is faulty. Car would not start when the car is parked in the sun. Need to remove the steering to get to the switch.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.