Here is a link that will play it out for you.
The switch is screwed into an oil filter adapter located at the oil filter. You will recognize it by the wiring on it.
bottom of the block
Just above the oil filter-in the engine block-They make a socket to remove them-get them at the auto parts store.
the sender is located on the oil filter adapter housing.the single wire switch is one inch below the oil filter. the adapter gasket is also pron to failure.
ask your mom
Remove transmission oil pan for access
The engine block coolant drain plug on 4.3 liter Chevy Blazer is located on the bottom of the engine, near the oil filter. It allows coolant to be completely drained from the block during maintenance.
Assuming it's the ever-common 3.1 liter V6, it should be on the front of the block between the radiator and the block.
I was looking at fordparts.com and it shows ( 1 ) engine oil filter . Motorcraft ( FL-820-S ) for the 4.6 liter Romeo engine , the 4.6 liter Windsor engine and the 5.4 liter , even if the engine has the block mounted engine oil cooler with remote oil filter
you have to remove the intake and it is located inside the engine block,you can see it once you remove the intake........
You will have to remove starter, It is behind the starter in the block.
Remove fuel tank
remove old heater and screw in new
Its near firewall. Have to remove exhaust manifold,Inlet housing to waterpump,and block.
depending on which engine you have...majority of caravans have the 3.0 liter engine and the air filter is beside or to the left of the battery. You need to unlatch the air filter cover to access and remove the filter
You must remove the skidplate on the underside of the truck and then look up.
The oild pressure sensor Is below the oil filter on the engine block. The knock sensor is above the oil filter. The vtec oil pressure sensor is on the block next to the distibutor. For a Vtec model and the 2.3 liter models(on the Si-Se models). On the 2.2 non-vtec(S model) I believe it is on the block above the oild filter
On the passenger side of the engine block near the oil filter. If you have th 4.7 Liter V-8 the oil pressure sending unit is directly above the oil filter on the driver's side. To be able to easily remove the connector, remove the oil filter , On the connector slide the red tab sideways, push down on the plastic tail on the rear of the connector and slide it back. Use a 1 and 1/16 inch DEEP socket to remove the sensor or if you have to, a wrench. You can do this without removing the filter but you will need to remove the connector blindly.
On the block near the oil filter. Right rear of the engine
The 5.7 liter 350 cu. in. Chevrolet V8 is a small block. There is no big block 350.
The 2004 Chevy Malibu 3.5 liter engine fuel filter is located inside of the fuel tank. You will need to remove the fuel in order to access the fuel filter.
Yes, It has a crank sensor. Its located above the oil filter on a 2.4 liter engine. Remove the oil filter for easier access.
Remove the skid plate under radiator and look at front of motor.
If it is a 3.0 liter, 10 mm socket on an extention with ratchet ( to remove air filter box) and a swivel adapter on a spark plug socket with ratchet and extention. Spark plug wire boot puller is also advised but not absolutly required List one ratchet, One 12 inch extention, one swivel adapter, one 10 mm socket, one 7/8 spark plug socket.
Changing the oil is pretty much a straight forward procedure.Except with the 3.0 liter engine.The oil filter is next to the positive cable of the starter.This is not good.You must disconnect the battery before you attempt to unscrew the oil filter and remove it.If you remove the filter without disconnecting battery,it will arc off of the positive end and catch fire.This is from experience!