Headlights Tail and Brake Lights
Ford Contour
Ford Trucks and SUVs
Ford E-150 Van

How do you remove the outer lens cover on the headlight of a 1992 Ford pickup?

848586

Top Answer
User Avatar
Wiki User
2011-09-12 20:32:47
2011-09-12 20:32:47

you can't. You have to replace the whole headlight assembly, it doesn't come apart. check the junk yards or eBay it's cheaper.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

with your headlights on (headlight doors up) remove the three screws that hold in the black plastic cover over the headlights, remove the torx screws (the 2 top outer ones) that keep the metal brace over the headlight, pull the headlight out of the connector and replace.

User Avatar

Remove the parking/turn signal light assembly. Take off the grill. Remove the headlight bulb. Remove the inner and outer attatching screws and upper attatching screw. Lift the headlight out.

User Avatar

The head light is a sealed unit. The outer sense is not removable.

User Avatar

The oil filter element is located on the right side of the engine. There is an outer cover and an inner cover that you will need to remove. The outer cover is round and can be identified by three bolts. Remove the three bolts and remove the cover. Now remove the inner cover. It has two bolts that are located to the right of where the outer cover was located. (you can see the inner cover bolts to the right before even removing the outer cover) Inside you will see the paper oil filter element. Also, there is an O ring on the inside of the inner cover. The owners manual recomends you change the O ring when changing the filter. After changing the filter and O ring, the specified torque for the inner and outer cover bolts is 7 ft-lbf or 1.0 m-kgf.

User Avatar

Step 1 Pop off outer plastic cover next to headlight switch Step 2 Look inside the square hole then press the retractable button to remove headlight switch Step 3 Remove screw hidden behind headlight switch Step 4 Pop off plastic cover (if you have heated seats, remove outer cover first to remove switch) Step 5 Remove screw hidden behind cover (or switch) Step 6 The plastic bezel is held in by the 2 screws you just removed and clips up top Step 7 once bezel is out, remove one screw on each side of gauge cluster Step 8 Cluster sits on 2 rubber grommets at the bottom. Wiggle it to an angle to get it out then unplug the 2 connectors at the back of the cluster (3 if you have ABS) Step 9 Wiggle some more and you're done!

User Avatar

First, unplug it from the back. Then remove the screws in the chrome ring. You will see a ring around the outer lip of the headlight. This will have screws on it. 3, I think. Anyway, remove these. Now, you will see screws with springs by them. These are for aiming purposes, only.

User Avatar

Remove outer headlamp ring by lifting tab. Remove the bulbs. Be careful and pull the headlight straight out after removing the bulb. It is attached to four plastic tabs and requires a good tug. Push the new headlight back on. You'll probably have to re-aim the headlight. I find it's easier to raise the hood,lLook behind the headlight assembly and remove the socket/bulb, then remove the bulb from the socket, replace and re-insert the socket/bulb. Be sure not to touch the bulb glass while doing this as it tends to shorten bulb life.

User Avatar

1996 Legacy: 1. Remove electrical connector. Must push in on sides. 2. Remove outer rubber boot. 3. Unlatch retaining spring. 4. Remove bulb

User Avatar

release the clips that hold the headlight in position and remove the headlight.if the model contains 2 covers the fog light is under the outer cover. one cover models the fog lamp is the innermost bulb.remove the clips and take out bulb.use a tissue and refit the new bulb. box up system

User Avatar

First, flip your headlights up. Then take the black cover of each Headlight Mount (should be 4 Torques each...T15..if memory serves me right). After the cover is removed, there will be two screws (Phillips); one on the top of the headlight and the other on the outer side. The screw on the outer side adjusts left-to-right, the upper screw adjust up-to-down...let me know if you run into trouble.

User Avatar

remove 5 screws holding windshield. remove whole headlight assembly. take flash light and look in headlight opening and find 4 nuts holding fairing to mounting brackets-2 nuts per side.. remove nuts. then remove your light bar-2 bolts per side..disconnect harness for light bar from inside fairing..remove fairing

User Avatar

it clips on to the base by little "hooks" on the outer edges

User Avatar

NO. The fuel pump relay on outer firewall by W. wiper motor, under plastic sheild/cover - drivers side.

User Avatar

[1] There is a round plastic cover on the outer most high/low headlight bulb. You'll be able access this cover more easily on the driver side. Removing the coolant overflow on the passenger side will be required (3 bolts on top of the container) to access the associated bulb unit. Twist the cover to loose the cover. Less than a 5 degree rotation is required. Remove the cover. [2] Remove the power connection from the bulb by pulling straight back on the connector (Black rectangular component in the middle of the bulb area). [3] There is a hinge holding the bulb in the unit. The notch holding the hinge closed is located at the bottom of the bulb assembly. Release the hinge and pull the bulb out. [4] Conduct steps 1 through 3 in reverse using the replacement bulb. This procedure is a little rough but you should get the idea when you examine the headlight assembly. There is no need to remove the entire assembly or any of the grill components.

User Avatar

Open the hood, behind the lights there are 2 flat plastic straps. Pull up on straps, that will allow you to pull the headligt out and replace bulbs On the front of the vehicle there should be a ring around the headlight there should be 4 bolts around the outer part of the ring remove the bolts and the headlight will pull out. (make sure to unplug hesdlight before you remove it).

User Avatar

Remove the four bolts holding the clutch pressure springs, next remove the outer cover. รŠRemove the clutch pack and soak in oil, replace the cover with pack in position and use a new gasket put the cover back on and fill with oil.

User Avatar

The oil pump is in the timing chain cover. The oil pan, pickup tube, and chain cover has to come off. Once the chain cover is removed you can remove the oil pump cover. The cover should be checked with a straight edge to be completely flat. You can then replace the inner and outer rotor and reassemble. The relief spring valve should also be checked but I'm not sure of the specifications for that. The oil pump is a fairly high precision and involved job.

User Avatar

take the bolts off the thing should fall off, oil everywhere, its great!

User Avatar

To the left of the steering column remove the panel (4 screws) that sits inside the outer headlight switch panel. The fuse panel is there.

User Avatar

You have to remove the entire headlight assembly to change the bulbs. Be careful not to touch the glass on the bulb, as the oil from you skin will shorten the life or break the bulb when it heats up. According to the manual and from what I've seen, there is two bolts on the inner side of the headlight assembly that need to be remove, then there is what looks like a cover with a plastic philip's screw that needs to be removed. Then towards the outer side and underneath of the headlights, between the front bumper there is another bolt that you will have to remove. This is about how far I got on the driver's side headlight, I wasn't able to remove it, because it looks like it's caught on something. From what I could tell, behind the headlight, on the outer side, it looks like there is a small box, maybe 1"x.5"x.5" and it has a clip on the top and bottom. I can't tell for sure if you need to push this through but it looks like it's part of the headlight. It should then just pull forward. I used a 10mm socket on the bolts and that seemed to work. I'm sure there is a standard socket that works better instead of metric, but I didn't have standard on me. The bolts shouldn't be extremely tight, so you shouldn't strip them.

User Avatar

To get to the parking light assembly, it's easiest to remove the headlight assembly. Open the hood. There are two metal bars just above the headlight assembly. Turn them towards you to unlock, then pull straight up. Remove the headlight assembly by pulling it towards you. Remove the bulbs (be careful not to touch the bulbs as grease from your fingers can make them blow prematurely). Set the headlight assembly aside. The parking light assembly has a hook on the outer edge, just behind the corner light. Farther to the center is another gray hook with a release. Press the release towards the corner light while pulling slightly on the assembly. Once released, swivel the light outwards to release the corner hook. Remove the light sockets and you're finished.

User Avatar

remove the outer cover,around 12 screws hold this in place,no need to undo screws for mud flaps.prise the cover from the bottom to top and remove.there is a conecter for number plate,just pulls apart.with cover off undo 4 bolts and bumper is off.

User Avatar

How do you remove outer door handles on Nissan dualis

User Avatar

remove all screws around outer door panel...remove inside cover of inner handle..remove torques screw..remove cover behind pull handle..remove torques screw...remove window control switch assy..remove screw..near top..hard to see but it's there..remove front upper triangular trim..pull up on panel..it will come off....speaker is bolted from the inside if you need to remove it...good luck....Ray

User Avatar

To remove the standard wheel cover stick the pry end of the lug wrench behind the outer edge of the wheel cover and simply pry it off. If your car has the wire wheel covers use the special wrench that comes with them to pry the center cap off then remove the retainer nut to remove the wire wheel cover.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.