answersLogoWhite
Hyundai Accent
Turn Signals and Hazard Lights
Grand Am SE

How do you remove the panel where the stereo is in a 1996 Hyundai Accent to replace the turn signal relay?

656667

Top Answer
User Avatar
Wiki User
2015-07-15 20:06:29
2015-07-15 20:06:29

The turn signal relay is behind the storage compartment on the left side of the steering wheel. All you have to do is pull the compartment out and there you are.

1

Related Questions

User Avatar

To replace the turn signal flasher in a 1998 Hyundai Accent, locate the flasher on the driver's side just above the brake pedal mount. The flasher is a plug-in device with three prongs. Unplug the old plug and plug in the new plug.

User Avatar

If your that stupid you don't need to be driving

User Avatar

Most cars: Pull your turn signal towards you.

User Avatar

The horn is location behind the front drivers side signal. You must open the hood, remove the signal lense, and if you look down into the bumper a bit you will see a small horn on a brackit that is being held on with a bolt just under the signal lense.

User Avatar

Simply by removing the front signal lense, First pop the hood open. Secondly, locate the front signal lense. Third, their is a screw on the top of the lense, unscrew it, pull the lense toward the front, than twist the light socket, replace the bulb. For reinstallion just work backwards. Good luck :)

User Avatar

The turn signal flasher relay switch can be found beneath the drivers side dashboard. The turn signal flasher relay switch will be to the left of the brake pedal.

User Avatar

The turn signal switch is quite easy to remove and replace. The turn signal switch simply plugs in and plugs out.

User Avatar

To replace a turn signal switch in a 1993 Chevy Lumina go to the trunk of the vehicle and find the plastic covering for the turn signal. Remove the cover and replace the bulb.

User Avatar

In most cases you will need to replace the turn signal switch on the steering wheel for your 1983 Chevy Caprice Classic rather than fixing it. To replace it, remove the horn pad and then use a steering wheel puller and compressor to remove the steering column. You will then remove the signal along with the wiring harness and bus fuses. Replace the signal and wiring and then replace the steering column itself.

User Avatar

Turn signal cam is broke. Remove steering wheel and replace it

User Avatar

If you are talking about the turn signal light. You have to remove one screw that holds the turn signal onto the frame of the car. Just look down staring at the turn signal and you will see it. Remove the screw, move the blinker forward and then remove and replace the light bulb. Reverse directions to reinstall.

User Avatar

If its the front turn signal you open your hood and partly remove the black plastic cover on top of your headlights. Then you should see a screw on that screws on your signal light. Remove the screw and take off the the signal light and then remove the bulb.

User Avatar

1. Remove the left front turn signal/parking light housing. On models with two horns the bumper cover must be removed for access to the right side horn 2. Disconnect the electrical connectors and remove the bracket bolts

User Avatar

When replacing the rear turn signal on a 1999 Acura Integra open the trunk. Locate the rear turn signal housings and find the bulbs. Remove and replace the bulbs.

User Avatar

Answer : unscrew the signal lens and remove the signal bulb and replace with 1157 bulb reverse process

User Avatar

If you remove the headlight assembly you will have access to the turn signal bulb.

User Avatar

You will need to remove the turn signal switch retaining screws. The turn signal switch can then be pulled outward. Remove the wiring harness from the and of the turn signal switch. Reverse the process to install the new turn signal switch.

User Avatar

remove side inner panel and remove the nuts and assembly will come out

User Avatar

To replace a turn signal on a 1994 Jeep Grand Cherokee prop the hood open. Locate the headlight housing and the turn signal will be located next to it. Find the bulb and remove it from the housing. Replace the bulb.

User Avatar

First remove the steering wheel, remove the torx screws and remove the house, remove the signal switch and the wiper switch, remove the torx screws and?æremove the ignition switch. Put in the new switch and replace everything in reverse.?æ

User Avatar

The front turn signal on a 1996 Blazer is accessed by using a Philips head screwdriver to remove the wheel well cover . Locate the bulb and twist to the left, remove. Replace with new bulb and replace the wheel cover.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.