The passenger side is the hardest. you need to move the A/C receiver dryer.To do this ther are 2 two bolts holding the bracket to the fire wall remove these then loosen the srew around the receiver so it is loose. You can now lift the receiver upwards , then you will have the clearence to put a socket on the nut and loosen it. I used a air wrench no problem.
the driver side I used an ratched wrench to get the nut. the powerbrake booster is close but you can get a wrench in there. Also I found it helpfull to use a air chisel to separate the knuckel to pull the ball joint out.
Follow the top radiator hose back to the engine. This is where the thermostat is. Remove the 2 bolts and there it is.
Remove - battery cable Raise and support vehicle Disconnect the wiring at the top of the starter Remove starter mounting bolts Remove starter
Remove the battery and the cruise control actuator. The starter has two bolts holding it in. Remove the bolts and wiring, then install the new starter. Re-install the cruise control and battery.
open the hood and on each side there will be a circular hole with a screw sticking out but on the sides there will be 2 bolts on one side and one on the other side. remove the 3 bolts. take off the tire and you will see that the strut has 2 bolts to undo it from the control arm. just take out those bolts and pop in the new struts and tighten the bolts back on.
To remove the back seat on a 1989 Ford Thunderbird, the first step is to remove the back of the seat. The back is held in by bolts on each side. After the back is removed, the seat area should come out after removing the floor bolts.
remove the two upper mounting bolts inside the trunk, then remove the one on the axl, replace bolts when you replace the shock...
Remove bolts, connectors and hoses. Replace. Hook up hoses, conectors and replace bolts. That easy!
remove the nuts from the u bolts and remove the bolts. Install new ones and tighten the bolts.
Detach lower ball joint from steering knuckle. Remove bolts that secure control arm to vehicle.
Remove serpentine belt, remove three bolts ,an 2 wires. The alternator will pull up off the motor to remove. Put new alternator in replace bolts, replace wires, an replace the serpentine belt..
loosen lug nuts remove pull bolts drop pan...
Remove the bolts, remove offending fan and replace with new one
Remove 2 mounting bolts and replace
If you have clearance just remove bolts
Follow the top Radiator Hose from the Radiator to the engine and you'll see a housing remove the bolts from the housing and there is your thermostat (Note the way it came out and replace it with a new one) make sure you know which way to put it back in
To replace the lower control arms on a 1994 Acura Integra safely raise and stabilize the car. Remove the lower ball joints and two bolts that hold the lower control arms to the car. Pull them off. Replace with a new unit.
You must separate the transmission from the engine. Then remove the eight bolts that hold it in place. Remove and replace.
remove bolts and replace it how do u think
remove starter boltsremove cable and wires
Remove 3 bolts, remove shock, insert shock, compress shock, replace bolts
Chilton manual says to remove the splash guard from the fender well. Then remove the bolts from the catalytic converter to exhaust bolts. Unbolt the manifold bolts starting from the two center bolts, two rear bolts, then the two front bolts. remove the manifold. remove old gasket. replace. If you believe that then it is a relatively simple job. Good Luck!
basically just remove the bolts holding it up, disconnect the harness, remove and replace!
remove bolts that hold hood to hood hinges place new hood in place, replace hinge bolts, do not tighten. line hood to where it needs to be, tighten bolts
V6 MODELS # Disconnect the negative battery cable # Remove the drivebelt # Disconnect the electrical connectors from the alternator # Remove the mounting bolts and remove the alternator V8 Models # Disconnect the negative battery cable # Remove the engine cover # Position the cruise control cable and throttle bypass hose asside # Remove the drivebelt # Disconnect the electrical connectors from the alternator # Remove the 2 upper stud bolts and the 2 upper alternator mounting bolts # Remove the 2 lower alternator mounting bolts and remove the alternator
In general, remove negative cable from battery, remove electrical wires from starter, remove bolts holding starter in place, remove starter. Replace starter in reverse order.