Power Steering
Pontiac Bonneville

How do you remove the power steering pump pulley from a 1998 Pontiac Bonneville 3.8L?

394041

Top Answer
User Avatar
Wiki User
2015-07-15 19:39:12
2015-07-15 19:39:12

Take the pump with you to an auto parts store so they can fix you up will a puller. Some places will let you "rent, borrow" these specialized tools.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

There is a specific tool for this operation. It is a power steering pump pulley puller. This grabs the groove in the end of the pulley and pushes the punp shaft away from the pulley. Available at your parts store.

User Avatar

to remove pump on 1997 Bonneville, I aligned holes on actual pulley wheel access holes and reversed bolts.........

User Avatar

You will need to remove the front engine cover, on your 1997 Pontiac Bonneville, in order to change the supercharger belt. Loosen the tensioner pulley to remove the belt.

User Avatar

To change the serpentine belt on a 2003 Pontiac Bonneville, loosen the tensioner pulley and remove the old belt. The tensioner pulley is the wheel in the belt system that has a bolt through the middle in a slot that can be adjusted. Put the new belt on and tighten up the pulley.

User Avatar

how do you remove the turn signal assembly on a 1989 Pontiac Bonneville

User Avatar

what tools do i need to remove the wheel cylinder on a 1993 pontiac bonneville

User Avatar

I have to jump start my Pontiac Bonneville 1988 everyday I drive it why is that.

User Avatar

how to remove a power steering pulley on a 1997 Nissan altima

User Avatar

The flasher on a 99 Bonneville is located under the dash below the steering column, remove the panel just below the column. It has screws.

User Avatar

How to remove left inner door panel of a Pontiac Bonneville 1996

User Avatar

You need to rent, borrow or purchase a power steering pulley puller. This tool will remove and replace the pulley without damage to the pulley or the pump.

User Avatar

You can remove your 1997 Pontiac Bonneville ignition switch by removing the retaining ring at the top of the ignition switch. The ignition switch will slide out.

User Avatar

Before you remove the evaporator core from a 1998 Pontiac Bonneville you need to have the air pressure discharged. You will then need to remove the AC unit. You will need to remove some screws before you can remove the evaporator.

User Avatar

That requires the use of a power steering pulley PULLER. ( A special tool ) The pulley is pressed on.

User Avatar

This requires a power steering pulley puller. This puller is designed to remove and install a power steering pulley without damage to the pulley and or pump. Attempting to do this without the puller will result in damaging the pulley or the pump or both.

User Avatar

Take off the sockets and remove the pump pulley.

User Avatar

To remove that pulley with out damaging the pump or the pulley you need a power steering pulley puller. This tool will also install the pulley. Your local auto parts store can rent or sell you that puller.

User Avatar

power steering pulley is pressed on. to remove pulley, u need to completely remove pump from vehicle and take it to a mechanic that has right tools for removing

User Avatar

No, you don't have to remove the power steering pump to remove water pump. You do have to loosen the 2 screws that hold the power steering pump and then move power steering pump about an inch or so, so you can have access to some of the screws that hold the water pump on.

User Avatar

That is not a Allen screw in there. That is part of the pump shaft. If you are looking to remove the pump pulley you will need a power steering pulley puller. This tool will help you remove it and replace it, without the puller you will damage the pulley or the pump or both.

User Avatar

You can replace the horn button on your 1992 Pontiac Bonneville by removing the center steering will cover. Remove the horn button retaining screws. Remove the horn button wiring harness. Reverse the process to install your new horn button.

User Avatar

Begin by removing the power steering pump belt from your 1991 Cadillac power steering pump pulley. Remove the power steering pump pulley retaining bolt. The retaining bolt will be in the center of the pulley.

User Avatar

You will need a power steering pulley puller. It is designed to remove and install the power steering pulley. If you attempt to remove the pulley without it you will probably damage the pulley or the pump or both.

User Avatar

The bolt has left-hand threads, and requires a lot of torque. Turn counter-clock-wise to loosen/remove the serpentine belt, then use a cheater-bar on your wrench to loosen the pulley-bolt (turning clock-wise).

User Avatar

Pulley is pressed onto pump, you need a puller to remove.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.