you must remove the 4 torx bolts from the axle mount and remove axle to give enough clearance to remove brake wheel cylinder
Most wheel cylenders have two bolts that come through the back of mounting plate but you also need to remove the metal brake line first it is best to use brake line end wrenches,"I bought mine at sears 'craftman' they look like a six point boxed end with just a little piece of the center cut out" to do this so you don't round off the break line nut and even then be careful or you will end up having to replace the brake line. If it gives you a hard time, make sure your brake line wench is on the nut properly and tap the wrench wit a small hammer also be carefull not to break off the bleader valve on top of the wheel cylinders back its just about dead center between the two mounting bolts. p.s. if your sunbird is a front wheel drive and a 2.0 have fun getting to the starter or any of the hoses at the back of the water pump it was a 2 day job on my wifes 94 sunbird
Disconnect the - battery cable Raise and support vehicle Disconnect wiring harness at top of starter Remove starter mounting bolts Remove starter
what tools do i need to remove the wheel cylinder on a 1993 pontiac bonneville
tools and knowledge (or a manual)
Check autozone.com it tells a bit about it. some engines you have to remove the timing belt so its not a very east job.
The center console is held on by several mounting screws. To remove it from a Pontiac Sunfire unscrew all of the mounting hardware. The center console will then be able to be pried off.
With a BFH ( Big Friggen Hammer)
After you have released the tension from the belt, remove the 2 obvious bolts that hold it to the engine block.
The 1994 Pontiac Grand Am ignition lock cylinder is held in place by the retaining ring at the top of the cylinder. Remove the retaining ring. Remove the wiring harness from the back of the cylinder.
Remove - batery cable Raise and support vehicle Disconnect wiring harness from starter Remove mounting bolts Drop starter
Disconnect brake lines Remove mounting bolts Remove Master cylinder Besure to "bench Bleed" new one prior to install
remove belt pump is accessable remove bolts make sure coolant is drained first replace
Remove hydraulic fluid line from slave cylinder (you may need to use a flared end wrench). Make sure master cylinder does not go dry!!! Unbolt slave cyliner from tranny, bolt new part on. Install hydraulic fluid line. DO NOT OVERTIGHTEN. Properly bleed system. Now your finished!
Unplug electrical connections Remove and cover brake lines Remove mounting bolts Remove master cylinder Install in reverse order BE SURE TO "BENCH" BLEED NEW MASTER CYLINDER PRIOR TO INSTALLATION
You can replace the ignition lock cylinder in your 1994 Pontiac Firebird without removing the steering will. Remove the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out.
Disconnect fluid linesRemove mounting boltsSlide cylinder out of booster REMEMBER TO BENCH BLEED NEW MASTER CYLINDER PRIOR TO INSTALLATION
Remove the serpentine belt. Tensioner is below Alternator. Remove the three mounting bolts on the tensioner baracket assembly. Replace entire unit.
remove air intake so you can get to it disconnect neg battery terminal , remove mounting bolts and detach ,installation is just reverse
Remove and plug brake lines Remove electrical connections Remove mounting bolts Pull master cylinder off activating rod BENCH BLEED NEW MATER CYLINDER Re-install in reverse order
how to remove key cylinder on 98 sunfire
Disconnect the brake lines Remove mounting bolts - pull master cylinder out of booster REMEMBER TO BENCH BLEED NEW CYLINDER PRIOR TO INSTALLATION
Rear wheel? Remove wheel Remove brake drum Loosen and remove brake line to wheel cylinder Remove mounting bolts at rear of wheel cylinder Pry brake shoes back from wheel cylinder Pull wheel cylinder off backing plate Install in reverse procedure Bleed affected brake line
Remove wheel Remove brake drum Loosen and remove brake line Remove mounting bolts Pry wheel cylinder off brake shoes Install new cylinder Replace brake lines Replace brake drum Bleed affected brake line
autozone.com current vehicle choose car repair info vehicle repair guides u can go from there
Disconnect the - battery cable Raise and support the vehicle Remove wiring at the top of starter Remove mounting bolts Remove starter
Remove and plug brake hydraulic lines Remove electrical sensor Remove mounting bolts Pull Master cylinder off activating rod BE SURE TO BENCH BLEED NEW MASTER CYLINDER PROR TO INSTALLATION Install in reverse order