The rear bumper cover is attached by 4 screws (behind the fender well covers, easily moved), and 4 screws inside the rear hatch. There are also 12 fasteners along the top and bottom of the bumper skin that can be pried out. Replacement fasteners cost about 5-10 dollars for a pack of 10. If you have a gray (non-painted) rear bumper, it only costs about $200 to replace it, and it's easily a DIY job.
Forget about the Toyota; Buy American.
if the bumper protector is damaged yes, or else the cover will have no suppot
Remove the screws in the wheel wells and underneath the plastic cover to remove the bumper cover. Then you can see to remove the actual bumper.
REMOVE TWO TOP BOLTS ON HEADLAMP ASSY. THEN REMOVE BUMPER COVER, THATS RIGHT THE BUMPER COVER, THEN REMOVE TWO BOTTOM BOLTS
To remove the rear bumper cover on a 1993 Ford Taurus wagon, the lights need to be disconnected in the rear. Once all electrical connections are disconnected in the rear, remove the taillights and the fuel filler overflow hose. Remove any nuts and bolts holding the bumper cover on. Using needle nose pliers, pop the push pins around the bumper cover upwards. Slowly pull on the bumper to remove it.
It is just clipped in. Just pull up - it will snapp off.
I do not believe there is a metal bumper. There is a foam insert that goes inside the bumper cover.
Unbolt the front of the wheel well liner inside the wheel opening.Remove the bumper cover bolt from the bracket located inside of the bumper at the end.AT the front of the car, remove the bolts holding the bumper cover on, located underneath the vehicle.You should now be able to remove the bumper cover from the front of your Dodge Intrepid.An instructional video has been included to show you the removal process.
Hi, I was looking for instructions as to "How to replace 1998 Toyota Camry rear bumper cover" and you got your question. If you have already replaced then please let me know otherwise I'm going to replace the part this weekened and I will let you know. Take care, Sam
rip it off
# Apply parking brake,raise the vehicle and secure it # working under the vehicle,detach the fasteners securing the lower edges of the bumper cover # Working in the front wheel opening,detach the retaining screws securring the bumper cover to the inner fenderwell splash shield # Pry out the lower edge of the splash shield,then reach up behind the bumper cover and remove the bumper cover fender retaining nuts # remove the fasteners securing the upper portion of the bumper cover and pull the bumper cover assembly out and away from the vehicle. # Disconnect any electrical connections which would interfere with removal
To remove the rear bumper on the 2005 Nissan Sentra, you will first need to remove the rear bumper cover by using a flat tool to pry the pins. Then, access the bolts holding the bumper to the frame of the vehicle and remove the nuts. The bumper will then lift off.
there are 3 5mm Allen nuts in the front. these are easy. the weird part is the back. there is a Toyota symbol in the back center. twist it counterclockwise till the shield is released.
1. If needed raise vehicle and support it on Jack stands 2. Remove the retaining screws in the wheel wells and along the upper and lower edges of the bumper cover. Remove the tail light housings. Remove the rear trim plate and pull luggage compartment trim out for access then remove the remaining bumper cover retaining screws. Remove the bumper bolts 3. On station wagons remove the rear window washer fluid reservoir for access to the bumper retaining bolts. The remaining bumper bolts are accessible from below 4. Pull the bumper and cover assembly out and away from the car
Remove the front bumper cover.... there should be 3 mounting bolts to remove the headlight after the bumper is removed.
how to install 2000 jeep grand cherockee Laredo front bumper cover
I have a small dent need to remove it
To remove the front bumper from a Celebrity: 1. Raise the vehicle as needed and put on stands. The parking brake should be on. 2. Remove the end covers 3. Remove the valence cover. 4. Remove the nuts that hold the bumper to the mounting struts. Be careful to avoid having the bumper fall off onto you. 5. Remove the bumper. Reverse these instructions to put the bumper back on.
This video on YouTube (see Related Links) will show you how to remove the front bumper cover from of a 2004-2007 Honda Accord.
Take off the bumper cover and it is right there
http://www.bfranker.badz28.com/fbody/repaint.htm this has everything you need to know to remove bumper cover just ignore the stuff about repainting unless that's what u plan to do
Park the Impala on a level surface and engage the parking brake. Remove the keys from the vehicle's ignition.Crawl underneath the front of the vehicle and use a slotted screwdriver to pry off the splash shield in each wheel well directly in front of both front tires. Once the shields are removed, you can access the screws securing the bumper cover to the fender.Remove the two screws on each side of the bumper cover with a Phillips screwdriver.Remove the bumper cover from the front of the vehicle by pulling it up and off the Impala. You may need another person to help you remove the bumper cover. Install a new bumper cover by placing it onto the front of the Impala.Crawl underneath the Impala again and reinstall the two screws on each side of the bumper cover. Reattach the splash shields to the wheel wells.
You have to remove the bumper cover, under bumper, and hood latch cradle. Then the ac condenser can be moved aside. Then remove fans and lines. Then remove radiator.