How do you remove the rear seat BACK on a 1991 Mercury Capri?
They unscrew from the back of the light assy. You may have to remove the light to get ot it.
Is it normal on a 1991 mercury capri when you want to switch on the lights you have to switch them on them back to daytime lights and back on for the taillights dashboardlights to turn on too?
no. try replacing the headlight switch... eBay
look in the back by the engin about a foo1 down its a very little filther its going horizantle kinda hard to get to but not that bad
I do bleave thet is under the back seat(just remove the seat and there is a plate there for the fuel pump) I think it is ther But I may be rong.
This is a difficult job. The front spindle assemblies must be removed. Then the assembly is pressed apart and the rotars are unbolted from the back. I tried this without proper tools and bought new bearings in the end. If you are mechanically inclined its probably better to remove the assemblies and take to dealer.
Remove the instrument panel cover. Remove the tachometer retaining screws. Remove the tachometer cable from the back of the tachometer. Reverse the process to install the new tachometer.
Mercury Capri 1991 runs but won't stay running Stalls out after you get going. Replaced distributor new plugs wires cap and rotor It will stutter like it loses fuel for a second and picks back up on o?
Check the compression in your cylinders
How can remove the rear seat on a 1990 mercury sable
in the fuel tank under the back seat. take out the back seat it just pops up and out and t is right there easy as pie to get to.
You remove the center seat and slide the back one up into it's place.
Remove the radio retaining cover from your 2000 Mercury Villager radio. Remove the radio retaining screws. The stereo will slide out. Remove the antenna cable and the wiring harness from the back of the stereo.
possible plugged fuel filter under hood, or bad fuel pump (access hatch under back seat)
You need to do a lot if it is like my 1995. You need to remove the back seat remove the back of the back seat remove the screws holding the rear deck.. where the speakers are. then remove the screwss... what a pain.
front or back
Remove the right wheel, then get down underneath it, remove the splash shield, back off the adjuster, remove the belt, and unbolt it.
on the back of the engine u have to remove the intake to get to it
What do you do when you turn the ignition key on to start on a 1984 Mercury Capri 5.0 but it does not stay running when the ignition is brought back to the run position?
replace the balist resister replace the balist resister
Pull the clips back and lift them off.
Remove the back seat cushion by pushing it horizontally back and then lifting up vigorously. Remove the two large nuts holding down the seat back; lift up and off on the seat back. Remove the rear deck cover by sliding forward. Unscrew the speakers.
Take out the bench seat, and remove the back, take a look. Holes are small.
Remove the rear speaker cover from your 1999 Mercury Cougar speaker. Remove the rear speaker retaining screws. Remove the wiring harness from the back of the speaker. Reverse the process to install the new speaker.
A fairly simple one. First, push the front seats as far forward as you can. Get in the vehicle and center yourself in front of the rear seat. Place both hands on top of the seat bottom and as you push hard down..also push backwards. The seat should dislodge from the two retainers holding the bottom of the seat in place. keep trying as this takes a bit of finessing to get the procedure down… Read More
push back and lift the front up the back is on tabs make shure there are back in place when puting it in
Look inside the trunk for the wing nuts to remove the unit.
Open the hood of the engine compartment. Locate the light bulb connector on the back of the headlight. Take hold of the light bulb connector, push in and turn at the same time. The light bulb will come out.
it's located on the firewall right in back of the intake
To remove the seats in the Mercury Villager you first need to pull the side lever and push the seat forward. Next, pull the release strap. Lift the back of the seat until the seat clears the latch. Pull rearward and remove from the vehicle.
push in hard on the bottom of the cushion then pull up
remove the 5/8 nuts on the side of the gearcase also the two under the cav plate and the back one the gearcase is the same as all of mercury,s v-6 outboards 81-current
After you unhook the front latches, push back to unhook top from the back ledge. Roll the rear window under first, push the top back slowly and then push the 1st(front) roller bar backwards as the top is falling into the backend. If you don't, the top won't fit flush. It took me FOREVER to figure this out! DONT FORGET TO USE YOUR KEY AND POP THE LEVER ON THE DRIVERS SIDE!!!!! DID YOU FORGET… Read More
it is on the back valve cover, you can't see it unless you remove the intake plenum.
the rear speakers are located in the back doors. you have to remove the door panels to get at them.
The starter is mounted at the top of the transaxle at the back of the engine. You can see it clearly if you remove the air filter box.
Buy a Haynes/Chilton manual at any auto parts store for 20 dollars. If you don't know how to remove them, you probably will not get them back on correctly.
You can go to a Mercury dealership. They should be able to cut another key for you. I did this with my car when I needed another copy. However, they may only go back so many years. I was able to replaced a key for a 1991 model, but they could not replace one for my 1990 model, and that was a few years ago. Still, they should be able to direct you even if… Read More
Drain coolant and remove a/c and front gear cover then remove water pump then install back together
Begin by removing the belt from your 1999 Mercury Mystique alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.
Loosen the tensioner locking bolt and and back off the screw. Consult a manual if you are not familiar with how to do this.
Remove the wiring harness from the back of your 1993 Mercury Villager windshield washer motor pump. Remove the windshield washer pump hoses. Remove the windshield washer pump retaining bolts. Reverse the process to install your new windshield washer motor pump.
Remove the belt from your Mercedes-Benz alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.
Unless I'm missing something, just remove the 4 bolts, 2 in front and 2 in back, 13mm socket?
Fuel pump Mazda 626 The way I did it was remove the back seat and there is a panel under the lining, unclip wires and loosen bolts!
grab the end of the key sticking out and pull straight back.
When you want drop a lot of heavy loads and need to pull it out, just yank it out.
On that year, You can just REMOVE the battery cable for about 10 mins. Then hook it back up.
Take brakes off and then remove 3 bolts from back of spindle and slide it out. easyest I ever did
Remove the wiring harness from the back of the blower motor. Remove the fan from the front of the blower motor. Remove the blower motor retaining nuts. Reverse the process to install the new blower motor
To remove the back seat from most GM vehicles, Lift the front of the seat section then pull the seat forward. After the seat bottom is removed, there should be a couple bolts holding the bottom of the seat back into place. After removing those bolts you should be able to lift the seat straight up and remove it.
The fuel pump relay on a 1991 Nissan Sentra is in the gas tank. To get to it you have to remove the back seat in the car and you will see a compartment that is at the top of the gas tank.
remove the neg (-)battery pole and plug in back in about 5-10 minutes