How do you remove the seat frame of a 1981 corvette?

To remove the seats from a 1995 Corvette, you will need to remove the front and rear nuts from the seat frame studs. You will?æalso need to remove the lug wrench that is attached to the seat frame studs.

The seat cushion has wire clips on both sides.Face the cushion head-on,grab each side and squeese towards center while pulling.

Behind the driver's seat.

Remove four bolts. Lift it out.

the easy way is to un clip the seat the clip is located under the front seat cushion by filcking the wire clip back its a wire clip lift cushion off then there are four bolts which unbolts seat to frame you will need to unplug wiring for seat motor you will see when you remove cushion then lift seat out

Remove the nuts! They are on the lower metal frame the seat

Should be a bolt in each corner of the seat and disconnect wiring harness

Put your head down in the footwell and look at the bottom (center) of the seat. You will see a small silver wire about 3" long. Push this wire down and back toward the back of the seat, when it pops down simply pull the seat cushion up.

It's in the compartment behind the passenger seat. Lift out the box and it should be there.

Open hatch behind drivers seat......remove battery cables.....remove battery hold down clamp at lower back flange of battery...pull out battery....replace in reverse order.

On my 2001 Astro there are 4 bolts from the seat frame to the floor remove the bolts and the seat is removable (HINT move the middle passenger seat back as far as it can go and that is easier to remove the seat and frame ..I have done this twice on the 2001 and 3 times on the 1989 I had..

Check behind passenger seat. Lift out compartment tray, it should be there

Four bolts under seat from frame into flooring, remove and lift out seat. Unplug any electrical connections as needed before removing seat from car.

look around the bottom of the seat their should be bolts leading through the floor board take those out (their should be 4 of them) and just remove the seat.

Four bolts hold the seats in. Pull the seat all the way forward & remove the two bolts behind the seat (one each side). Push the seat all the way back & remove the front bolts. The seat should come right out (mine did!).

On most models, remove the screw that holds the rear seat bracket to the rear fender. Then slide the seat back so the front mounting bracket slides out of the frame. On many softtail models, there is a bolt on each side of the seat that attaches the driver seat to the frame. These must be removed before the seat can be slid back and off the motorcycle.

The seat height of a 1981 Yamaha Maxim 550 is 29.3 inches. That height not really adjustable, but frame modifications would probably lower it.

fold seat down, then unbolt the frame of the seat, and remove them. it is a really simple process.

Way up nder the drivers side dashboard. This is true and very difficult to reach for an extended amount of time. If you are troubleshooting this for a long time spend the 30 minutes to remove the seat.

Under the rear of the tunnel there will be studs with nuts on them. Remove the nuts, lift the seat until the studs clear the tunnel frame. Pull the seat back to release the front retainer, now you can lift the seat, and unplug the wiring, and remove the seat.

Remove lower seat bottom. Remove two bolts from bottom of seat back. Lift seat back off of its hooks. Remove from car. Use Philips screwdriver to remove 4 screws holding speaker grille to seat back frame.

what is the process for installing new seat covers in a 1977 chevrolet corvette

remove seat, remove neg cable from frame and Pos from battery, remove strap and take out battery.

First you have to remove the two plastic side tail pieces, then you will find two bolts, one on each side, that fasten the seat to the frame. The seat is now loose.

You have to remove the 28 mm bolts at the rear of the passenger seat on either side of the tail light. Now slide the passenger seat back to release a clip holding the front edge of the passenger seat. Then remove the 12 mm bolts holding the seat to the frame.