How do you remove the shift lever on 1997 Buick Riviera?

Location of Neutral safety switch on Buick Riviera?

You do not give a year, engine size, trans type........ so the generic answer is on the shift shaft of the transmission behind the shift cable's lever and mounted to the trans case. On a FWD trans, it is a foot below the brake master cyl.

Do you have to remove the shift lever to remove the transmission on a manual shift 1995 Toyota pickup?

you dont have to but it makes it a lot easier.

Where is the mower Deck Safety Switch on MTD yard machine?

The switch is located inside of the frame, underneath the panel where the shift lever comes up. Remove the knob on the shift lever and remove 2 screws, and remove the plate. The switch is mounted below the Deck Lowering Lever.

How do you adjust motorcycle gear shift angle?

loosen the bolt on the lever, remove the lever and replace in the new angle, then retighten.

How do you remove the gearshift lever on a 1997 Ford Thunderbird?

Press the shift lever detent button then lift up sharply

How do you remove the floor console on a 1965 Buick Skylark automatic for repairs?

1. Remove the knob from the shift lever (it is threaded onto the shift lever). 2. Remove the shift indicator assembly from the console (it is held in place by either 1 screw or 1 rivet located at the rear of the shifter slot). 3. The console is attached to the shifter assembly by two screws and also attached to the floor by screws located inside the storage compartment. If you need more info, I have a dealer's 1965 Buick chassis and body parts book (printed in May of 1965) that has many parts break down figures with all of the GM part numbers.

How do you replace a manual shifter in a 1995 cavalier Z-24?

* Remove the shift lever knob,console and shift boot * Disconnect the shift and select cables from the shift control assembly * Remove the large shift cable retainer plate and detach the cables from their bracket on the shift control assembly base * Remove the shift control assembly retaining nuts and remove the shift control assembly

How do you remove manual shifter and boot in 2001 Nissan maxima?

* Disconnect the negattive battery cable.On airbag-equipped models also disconnect the positive cable then wait three minutes before proceeding * Raise the car and support it securely on jackstands.Remove the cataltic converter heat shield * Disconnect the support and control rod from the transaxle * Remove the nut and bolt tht attach the control rod to the shift lever.Disconnect the return spring,remove the nuts that attach the support rod to the shift lever socket and mass damper and remove the shift linkage assembly * Remove the console.Detach the shift lever dust boot from the floor,pull out the shift lever and slide off the dust boot,seat,insulator and shift lever socket.

How do you change gear shift knob on 1979 trans am?

Please be aware that for 1979 - 1981 Pontiac Firebird/Trans Am models no unique service manuals were created. Instead, model year-specific supplement manuals were printed, which detailed new data specific to their respective model years. In other words, because the shift knob assemblies from 1979 - 1981 models were no different from the 1978 model year, the 1979 supplement manual refers the user to the 1978 service manual. This is why the "7B-21_pic" service manual image says it's from the "1978 PONTIAC SERVICE MANUAL". automatic transmission SHIFT CONTROL LEVER - R & R (Fig. 7B-23) 1. Release shift control lever by inserting a thin rule or a piece of .015" - .020" shim stock into socket along side base of shift control lever on driver's side. 2. Insert rule or stock to depth of at least one inch to unlock its bayonet retainer and lift control lever and tool up out of shift socket. 3. Install shift control lever by inserting into shift socket. Bayonet retainer will lock control lever automatically into proper position. manual transmission SHIFT CONTROL ASSEMBLY - REPAIR (Fig. 7B-21) 1. Remove shift lever shaft retainer and shaft from control lever housing. Then, remove shift control lever assembly from control lever housing. 2. Note position of spacers in relation to shift levers and remove spacers and shift levers from control lever housing. 3. Remove spring bracket and spring from shift control lever assembly. 4. Remove retainer and control lever pivot pin from shift control lever assembly and separate control lever bracket from shift control lever. 5. Clean and inspect all components. Replace all worn, cracked or broken parts as necessary. NOTE: If necessary to remove reverse lever adjusting screw, grind or chisel off the weld and remove screw from control lever bracket. 6. If adjusting screw were removed, position shift control lever bracket and install pivot pin and retainer. Install reverse lever adjusting screw but do not weld at this time. NOTE: Lubricate all levers and spacers with water repellant-type of lubricant such as lubriplate or equivalent. 7. Install shift levers and spacers in control lever housing. 8. Install spring bracket and spring in control lever bracket and shift control lever assembly into control lever housing, making sure lever engages shift levers. 9. Install shift lever shaft and retainer. 10. If removed, adjust reverse lever adjusting screw as follows: a. Position shift control lever in 1st-2nd shift lever and touching interlock plate spacer between 1st-2nd and reverse shift levers. b. Hold reverse selector rod agains the adjusting screw, tightening screw to eliminate any contact of the control finger as it travels across neutral gate of interlock plate spacer. c. Weld screw securely in place. http://hotfile.com/dl/26587081/fa5f595/7B-23_words_and_pic.jpg.html http://hotfile.com/dl/26586993/c9e8897/7B-21_pic.jpg.html http://hotfile.com/dl/26587044/b143eef/7B-21_words.jpg.html

How do you remove the shifter on a 1994 ram 3500 manual transmission?

remove shift knob remove shift boot at the base of shift lever, there is a metal ring, push down, and turn it to the left. -there is a special tool to do this, but two flat head screw drivers work

Whats up with my 1995 buick riviera the floor gear shift is in park but the indicator light says its in a different gear so it wont start?

if I'm thinking correctly its a bracket...

Shift lever will not lock into a gear?

700r4 gear shift lever want lock in place