answersLogoWhite
Nissan Stanza

How do you remove the speedometer housing on a 1991 Nissan Stanza?

373839

Top Answer
User Avatar
Wiki User
2005-01-19 06:15:17
2005-01-19 06:15:17

The question you ask is too involved for a proper answer. You may want to go to a car parts store, or book store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.

1

Related Questions

User Avatar

First remove the tailights then the trim piece on the rear body pannel(where the stanza emblem is) then you will see the bolts for the bumper hope this helps.

User Avatar

Drain the water from your 1987 Nissan Stanza. Remove the water return hose from the water pump. Remove the water pump retaining bolts. Reverse the process to install the new water pump.

User Avatar

You will need to remove the tire and wheel from your 1992 Nissan Stanza. Remove the brake pad spring and caliper. The brake assembly will come off. Reverse the process to install the new brake pads.

User Avatar

Inside the distributer. Remove cap and rotor. Remove plate and there it is- small plastic piece.

User Avatar

The thermostat is located under the alternator and is attached to the bottom radiator hose. There are four bolts holding the thermostat housing to the block and two bolts connecting the housing to the bottom radiator hose. Remove the housing. You will need to use liquid gasket maker as there are no longer gaskets for the thermostat.

User Avatar

Remove the dashboard cover. Remove the retaining ring, from the speedometer. Remove the speedometer cable from the back of the speedometer. Reverse the process to install the new speedometer.

User Avatar

Remove cable from speedometer head and squirt proper lubricant through cable housing

User Avatar

Remove the two screws. Then remove the light housing. The bulb is right there, pull it out. Cheers

User Avatar

Remove the negative cable line from the battery and bleed off fuel pressure, next remove the thermostat housing cover, finally the spring of the thermostat should face the engine, so put in a new thermostat and seal with liquid gasket maker.

User Avatar

1980 corvette , how to remove speedometer

User Avatar

Remove the dash panel cover. Remove the speedometer retaining ring. Remove the cable from the back of the speedometer. Reverse the process to install the new speedometer.

User Avatar

you might have to remove the pass. door panel and the pop the little triangular piece off and it should be some screws behind that to diconnect it

User Avatar

The best place to spray starting fluid into your 2007 Nissan is the air cleaner housing. Remove the cover to the air cleaner housing and spray the starting fluid directly into the air filter.

User Avatar

You will need to remove the instrument panel cover. Remove the retaining screws from the speedometer. The lightbulb will be on the back of the speedometer.

User Avatar

There is no actual "plug". After draining the manual transaxle by unscrewing the bottom drain plug. Put the drain plug back in, then take out the speedometer sensor. There is a 10mm bolt that holds a bracket. Remove bolt and bracket and lift off sensor and speedometer shaft housing. Then remove the aluminum housing that contains the speedometer gear. It may require using a chisel. If you are lucky you won't destroy it by taking it out. Good luck! There is a stamp on the transmission housing describing where the fluid level should be.

User Avatar

Disconnect speedometer cable from back of speedometer gauge by twisting the threaded collar to unscrew. Then just slide the old cable out of cable housing and insert new one. If cable is broken you may need to disconnect cable from transmission tail shaft to remove part of the cable. Cable must be inserted into the gauge end of the cable housing.

User Avatar

Remove battery cables, remove the sterring colom covers top and bottom. remove the two screws from the cover and the cover. The speedometer cluster is in view. remove the screws on ether side and flip the cluster over. Then you can replace the bulbs by twisting then out. It helps to note the position of the bad light before you take it apart. Cheers .

User Avatar

I don't know what year, make or model you have but most transmissions have the speedo mounted in the tail shaft extension housing so, if you remove the tail shaft housing you can retrieve the speedo gear.

User Avatar

remove cable from the transmission and remove the cable from the back of the speedometer up under the dash and then the complete cable can be pulled out.

User Avatar

Pull the speedo and gauge package out of dash. Unhook wiring. Remove speedo cable from speedometer. Pull speedo cable out of housing, lube it lightly and re-insert. Hook everything back up and re-install gauges. Pull the speedo and gauge package out of dash. Unhook wiring. Remove speedo cable from speedometer. Pull speedo cable out of housing, lube it lightly and re-insert. Hook everything back up and re-install gauges. Pull the speedo and gauge package out of dash. Unhook wiring. Remove speedo cable from speedometer. Pull speedo cable out of housing, lube it lightly and re-insert. Hook everything back up and re-install gauges. Remove gauge package. Remove wires and speedo cable housing. Pull speedo cable out, lightly lube with grease and re-insert. Hook everything back up and re-install gauge packege.

User Avatar

Remove the cable housing from the rear of the speedo and pull the cable out, then take it loose at the trans and remove the piece that is broken off. Get a new cable and when reinstalling it grease it good with special speedo grease.

User Avatar

The fan housing on a 97 200sx is held in using 3 10mm bolts on the top of the fan housing. once you remove these 3 bolts and unplug the fans they lift right out

User Avatar

follow top rad hose into engine remove the 3 bolt housing and ul see it


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.