Remove the positive battery cable from your 1994 Firebird battery. Remove the cables from the front of your starter. Remove the starter retaining bolts. Reverse the process to install your new starter.
there is a ignition fuse under the hood, no starter fuse
Disconnect the - battery cable Raise and support the vehicle Disconnect the wiring at the top of starter Remove starter mounting bolts Remove starter
Disconnect the - battery terminal Raise and support vehicle if necessary remove wiring from top of starter Remove mounting bolts Remove starter
Disconnect the - battery cableRaise and support vehicleDisconnect wiring harness at top of starterRemove starter mounting boltsRemove starter
first disconnect the battery then remove the front gard that is pver thestater and then remove the two bolts that hold the starter on then you remove the wires that are conected to the starter and put the new one in
Disconnect the battery. Find the starter, and disconnect the wiring. There will be either two or three bolts holding the starter in. Remove those, and take out the starter. Reverse the steps to install the new starter.
Disconnect battery, remove electric wires from starter, remove mounting bolts, install new part in reverse sequence.
Is this the airplane? Remove one battery post connector. Remove wire connections from starter. Remove mounting bolts. Remove starter. Clean the bolts and starter hole of any dirt or grease. Install new starter with cleaned bolts and reinstall wires and battery connection.
Disconnect your battery, then remove the two nuts from the starter wire harness. Pull the wire and cable of the studs. Remove starter bolts and slide starter out of bellhosing.
If its the same as my 95 eldorado (4.6 northstar) you need to remove the intake manifold , the starter is in the valley pan.
Remove ground cable. Safely lift vehicle; place on jackstands. Remove any brace that obstructs. Remove the 2-3 bolts that hold the starter in place and as you drop the starter, remove the wires noting there location. Reverse process. Done.
How do you reset the security code on a 1994 ponitac firebird formula......
You can find the 1994 Pontiac Firebird window relay switch inside of the drivers side door. You will need to remove the drivers side door panel in order to access the window relay switch.
There is no coil pack on that year.
After disconnecting the battery, disconnect the electrical connection on the starter solenoid. remove the starter bolts and the starter. Note the location of the spacer shim. Installation is the reversand make sure you replace the shim or you will get noise.
Does it crank? do you have spark? fuel?
under front of motor there are two bolts on bottom side of starter that's it but make shure you disconect battery and take the power wires off side of starter
life the front of the car up. so you can get under it,, the starter is on the passenger side of the tranny, there are 2 bolts holding it on.. but first you will have to diconnect the positive side of the battery,,, then disconnect the ehaust from the headers. don't forget to disconnect the O2sensor you will see it. it looks like a spark-plug on the ehaust next to the driver side header..... you have to drop the ehaust so you have room to remove the starter. once the ehaust is down, remove the 2bolts holding the starter in place. when the starter is free to be moved around. spin it around tell you see the solenoid, you will see 2 wires you have to disconnect. now the starter is ready to come out.. good luck
1hrs 34mins94 minutes is 1 hour and 34 minutes
This truck uses three different engines, all with slightly different starter mounting. All starter replacements are pretty similar though. Most importantly you must first disconnect the negative battery cable. Raise and support the vehicle. From under the vehicle remove the large and small power wires to the starter. Remove the starter mounting bolts Remove the starter. Reverse procedure for installation.
Disconnect the - battery cable raise and support vehicle if necessary Disconnect wiring harness at starter Remove mounting bolts Drop starter
BACK SIDE OF ENGINE, UNDER INTAKE MANIFOLD, BOLTED TO TRANSMISSION LEFT OF THE OIL FILTER
try an impact gun, or rest a breaker bar against the body or something and use the starter
disconnect neg batt cable, raise front of vehicle on jack stands, remove wiring from starter, remove 2 retaining bolts on starter attached to passenger side where transmission meets engine, lower starter. install in reverse order.remember, you must disconnect the motor mounts and lift the motor to gain enough clearance to remove the starter. on 94 4x4 se model. I just performed this task.
if you mean the 3.4 v6 123456