I just had mine replaced and I was having the same problem with getting the wiring to come out. I watched the man while he was replacing it for me. There is a orange insert thing at the bottom of the wiring plug. He pushed the top of the plug out(not all the way, as much as it could go) with a screw driver and then pressed on a release type button in the front and it came out.
Just replace mine on 2003 caravan, orange tab at bottom of plug slides out 1/4". then press tab at top in. Plug will slide right off.
From outside,take a screws out to get light assembly loose and remove light socket from back of assembly and channge your light bulb,then put it back.
Not possible. You have to remove the whole light assembly.
I just changed the whole headlight assembly in my 1997 grand caravan. However, to change the parking light or turn signal indicator light, there is a round plastic plate in the front fender well in front of the tire. Pop this out and reach in and unplug the socket from the light assembly, change the bulb and install in reverse order. Good luck!
Where is the brake light fuse found on a 1996 dodge grandcaravan
Remove the wiring harness from the tail light assembly in your 2005 Mercury. Remove the tail light assembly retaining bolts. The tail light assembly will come out.
you need to replace your fan relay switch, in my 2000 caravan i had to remove thel left head light to reach it
If you open tailgate there should be 2 black screws against rear fender - remove these and assembly should pull-out
The tail light is an assembly. The lens is not removable. To replace a bulb you remove the assembly by opening the liftgate, removing two fasteners, and pulling the light rearward.
Look inside the trunk for the wing nuts to remove the unit.
there are two or three screws on the inside where the light is. Take those out, and the whole assembly pops out. You also need to unplug the cable that connects the whole assembly's circuit board if you want to completely remove/replace the assembly.
more information needed is it in the window or the design in the spoiler
Remove the wing nuts from inside the trunk, the assembly will pop out.
That is the check engine light.
You will need to remove the tail light covers in the cargo compartment. Remove the wiring harness. Remove the tail light assembly retaining bolts.
You have to remove the whole headlamp assembly. Remove the 1 bolt 6mm? and pull outwards.
Have a look at this link: http://www.wikihow.com/Replace-a-Tail-Light-on-a-Dodge-Grand-Caravan
depending on the year I have had issues with a 1990 and a 1992 grand caravan problem was the light in the glove box the contact would turn the light on periodically draining battery
remove it and it wont start if that light burns out oris removed the eng wont start it shuts down the computer on most new modles
To change the flasher in the front, remove the circular plastic cover in the wheel well by rotating and you can reach the bulb assembly and unscrew the bulb. if it is in the rear you just undo the one screw and it slides off. if in the front there are a few bolts holding it on under the hood and behind the light assembly.
You can access the Nissan taillights from the cargo compartment. Remove the tail light assembly cover. Remove the tail light wiring harness. Remove the tail light assembly retaining bolts.
Remove bolt on top of headlamp assembly. Gently pry and pull assembly straight out. Bulb can now be acessed.
Open the trunk, locate and remove the defective bulb from the socket assembly in the tail light assembly. Replace the bulb with a new one, and lock into socket. Close trunk.
Open the trunk and remove the nuts holding the assembly in place. With nuts removed the tail light assembly will come out the back then you can remove the light socket to replace the bulb.
The map light on a 2004 Dodge Grand Caravan SXT is changed gently prying the edge of the cover to reveal the bulb. The bulb can then be popped out and a new bulb installed.
drop the tailgate on side of bed where tailgate closes are couple of screws. thses hold the light assembly in bed. remove thse ,then remove light assembly light bulb is the able to be removed from back of assembly