answersLogoWhite

0


Best Answer
Copy

Look at the belt and find the tensioner. You have to remove the tension from the belt in order to remove it. Different tensioners have different ways of removing the tension. On some there is a hole in the end that you insert a ratchet in and pry to remove tension. On others you just pry the idler one way or another to remove tension. If you look carefully you will figure this out. Be sure and check the idler and make sure it is in good condition. If it is loose or rolls with a noise, now is a good time to replace it.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:31:04
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you remove the tension to put a serpentine belt on a 1995 Chevrolet pickup?
Write your answer...
Submit

Related Questions

How do you remove the serpentine belt from a 1994 Chevrolet Cavalier?

Using a 15mm wrench, turn the bolt in the center of the idler pulley clockwise to relieve tension and remove the belt.


How do you remove the evaporator on a 1994 Chevrolet pickup?

remove all the screws


WHAT PULLEY DO I loosen to get single drive belt on?

If you are referring to the Serpentine belt, you loosen no pulley. You simply remove tension from the belt. The tension is applied by the Idler Pulley. Pry the idler back and remove the belt.If you are referring to the Serpentine belt, you loosen no pulley. You simply remove tension from the belt. The tension is applied by the Idler Pulley. Pry the idler back and remove the belt.


How do you remove the radio in a 1995 Chevrolet pickup?

you pull it out


How do you loosen a serpentine belt on a 1989 Chevrolet truck?

If you just want it looser...its factory set....To remove it, locate the tension pulley and us a open face wrench to take off the tension...belt will come right off.


How do I replace the serpentine belt on a 2004 Matrix?

First you need a breaker bar and 19mm socket to fit the "tension bolt". Turn tension bolt clockwise to release tension in order to remove the serpentine belt.


How do you remove an ignition switch from a 1979 Chevrolet C10 pickup?

Remove the retaining ring from the top of your 1979 Chevrolet C 10 pickup truck ignition switch. Slide the ignition switch out and remove the wiring harness.


How do you replace the serpentine belt on a 1997 Chevrolet Cavalier?

Serpentine belts have a self-adjusting idler pulley that keeps the correct tension on the belt. The idler arm will have either a cutout where a ratchet wrench will fit without a socket or a nut where a socket will fit. Turn the idler arm either clockwise or counter-clockwise (whichever applies to your application) to loosen the tension and remove the serpentine belt. Installation is the reverse of removal.


How do you remove a window motor from a 1993 Chevrolet 1500 pickup?

you have to drill out the rivets


How do you remove the front bumper of a Chevrolet pickup?

You shouldn't own a chevy if you can't figure out how to remove the bumper


What is the serpentine tensioner in a 99 Isuzu trooper?

What about this tensioner? How do you remove it, or how do you releave the tension so you can replace the belt?


How do you release the tension on a serpentine belt for a 1998 Chevrolet S-10 truck?

It is quite easy, There is a spot to insert a 3/8" ratchet (No Socket) on the automatic belt tensioner. Simply use the ratchet like you normally would (I can't remember if you tighten or lossen to remove tension) and then use something like a block of wood or a helper to keep the tension off the belt to remove. The same to replace.


On a 2003 Ford F250 diesel how do you remove the serpentine belt?

Use a breaker bar in the belt tensioner to relax tension and then remove/replace belt


How do you replace a tension pulley on a 2001 Lincoln town car?

Disconnect the battery.remove the serpentine belt.Unbolt the pulley.


What to do when your 1970 Chevrolet pickup will not shut off?

Remove the battery cable, this is a sure way to get it to shut off.


Where is the thermostat located on a 1999 Chevrolet Prizm?

The alternator blocks access to it. You need to remove the serpentine belt, then the alternator to get to the thermostat.


How do you remove the fan from the water pump shaft on a Chevy Cheyenne pickup with a V6?

Pull the radiator shroud, remove the serpentine belt, remove the fan from the water pump shaft, then remove the water pump.


How do you change serpentine belt for a 2007 Chevrolet Aveo?

Take off pass. front wheel and cover inside wheel well. i believe it is a 3/8 drive ratchet into tension pulley and push towards front of car. The belt will get loose to remove.


How do you change a serpentine belt tension unit on a 1997 Buick Skylark?

Remove belt and tensioner should just be bolted to engine


How do you remove a ignition key tumbler in a 1977 Chevy pickup?

Remove the retaining ring from the top of your 1977 Chevrolet pickup truck ignition key tumbler. Slide the ignition key tumbler out. Remove the wiring harness from the end of the key tumbler.


How do you change a serpentine belt on an 88 Mercury Cougar?

To change the serpentine belt on a 1988 Mercury Cougar, first take a picture of how the old belt is put on. Then, loosen the nut on the tension pulley and remove the old belt. Use the picture to route the serpentine belt in the same pattern as before. Tighten up the nut on the tension pulley.


How do you change the alternator in a 1997 Chevrolet camaro V6?

disconnect battery. remove electrical connections from alternator. remove serpentine belt. remove alternator mounting bolts and remove alternator. Installation is reverse of removal.


When you remove and replace water pump what is the best way1997 gmc sonoma pickup?

-drain coolent -remove serpentine belt -remove clutch fan -remove rad hose going to water pump -unbolt and remove water pump


How do you remove ignition cylinder from 1975 Chevy pickup?

You will need to remove the retaining ring from the top of your 1975 Chevrolet pickup truck ignition cylinder. Slide the ignition cylinder out and remove the wiring harness. Reverse the process to install the new ignition cylinder.


How do you replace starter on 1988 Chevy 1500 pickup?

Remove the positive battery cable from your 1988 Chevrolet 1500 pickup truck battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.