answersLogoWhite

0


Best Answer
Copy

There ar two located directly in the coil packs. They are hrd to get to, bu once you get to the they come out easily. You have to slide the coil packs up just a ;ittle then pull straght out. Do not pull at an angle, because you will bend the electrical connections

User Avatar

Wiki User

โˆ™ 2015-07-15 20:06:34
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you remove the two coil packs on a 1988 Cavalier with a 2.0 four cylinder?
Write your answer...
Submit

Related Questions

How do you replace the thermostat located on a 1988 Chevy Cavalier 4 cylinder automatic?

Remove the water supply hose from your 1988 Chevy Cavalier thermostat housing. Remove the thermostat housing bolts. Lift the old thermostat out and drop in the new thermostat.


How do you change your fuel pump on your 1988 Chevy cavalier 4-cylinder .?

Remove the wiring harness from your 1988 Chevy Cavalier fuel pump. Remove the fuel lines from the fuel pump. Remove the fuel pump retaining bolts. Reverse the process to install the new fuel pump.


How do you remove an ignition lock cylinder from a 1988 Mazda 323?

With an uncle and a hammer.


Where is the distributor module on a 1988 Chevy Cavalier?

The 1988 cavalier and or jbody cars use a coil pack.You do not have a distributor and if a ignition issue is present replacing one or all coil packs are the answer.I originally stated it could have had a distributor but,was incorrect on my first response.As said if you replace the coil packs unhook your negative battery cable prior to any electrical work to prevent and problems and safety.


How do you remove the ignition switch from a 1988 Dodge Ram 50?

Ignition switch and lock cylinder removal 1988 Dodge Ram 50.Disconnect the negative battery cable from the battery.Remove the steering column cover to gain access to the ignition switch/lock cylinder.Using wire cutters, remove the cable band.Remove the bolts that hold the ignition switch/lock cylinder to the steering column.Unbolt and remove the key reminder switch and remove the switch lock cylinder from the steering column.


How do you remove the ignition lock cylinder from a 1988 Ford Thunderbird?

There will be a pin on the front bottom of the cylinder housing. Turn the key to the on position then push the pin in and pull the cylinder out.


What do you have to do to remove a starter for a 1988 Chevy Cheyenne 6-cylinder standard trans?

you must remove the clutch slave cylinder and line. Then unbolt the starser and install the new one


How do you replace the water pump on a 1988 Chevy Cavalier?

Drain the radiator on the 1988 Cavalier. Take of the water pump belt. If the fan and shroud are in the way then remove them. unbolt and remove the pump. Bolt up the new pump and put the belt back on. Put the shroud and fan on if they were removed. Fill the radiator back up.


How do you remove the headlights on a 1988 Cchevy Cavalier Z 24?

Begin by removing the wiring connector on the back of the headlight. Remove the headlight retaining bolts. The headlight will come out.


How do you remove fuel filter on a 1988 Toyota Pick up 4 wheel drive 4-cylinder?

there's a panel to remove located in the front drivers side wheel well.


How do you remove the control ignition module on a 1988 Chevy Celebrity 4-cylinder 2.5?

under neth the coil packs middle back of engine 3 bolts you will need a 10 milimiter 12 milimeter and 13 i did mine 4 TIMES !!!!


Where is the crankshaft sensor located on a 1987 Chevrolet celebrity 4 cylinder 2.5?

It on the back of the coil packs going into the side of the block.


How to remove a Power Steering pump on a 1988 Chevy Celebrity?

Does your car have the 4 cylinder engine or the V6?


How do you remove a lock cylinder for a 1988 gmc jimmy?

if it is the ignition lock cylinder, first disconnect the battery, you need to remove the steering wheel ,turn signal switch , etc, then you need to insert the ignition key into the lock cylinder, turn it to the run position,then pull the cylinder out, reverse the operation to install the cylinder,


Does a 1990 rm 125 cylinder fit a 1988 rm 125?

No, the 1990 RM cylinder doesn't fit the 1988 cylinder. The 1988 cylinder is the only year that'll fit on a 1988 motor. This was the first year Suzuki did that. It actually sucks because I have a 1988 RM 125 I've been trying to get a cylinder for. And the 1988 cylinder is the only match. Nothing else would fit.


How do you change a clutch slave cylinder on a 1988 Chevy S10 Pickup?

You will need to remove the transmission to replace the clutch slave.


How do i repair the slave cylinder on my 1988 Ford Ranger?

The slave cylinder on a 1988 Ranger can not be repaired. The cylinder will have to be replaced, then the system bled.


What is the firing order for a 1988 Chevy Cavalier 2.8L V6?

THE FIRING ORDER FOR A 2.8 V6 88 CAVALIER IS 1,2,3,4,5,6, THE COIL PACKS ARE 1-4 6-3 2-5 HOPE THIS HELPS YOU! Hey Ruth==It is 1-6-5-4-3-2 GoodluckJoe


How do you replace the starter on a 1988 Chevy pickup 8 cylinder?

Disconnect the - battery cable Raise and support the vehicle Remove wiring at the top of starter Remove mounting bolts Remove starter


How to change spark plug wires in a 1988 Chevy Cavalier z24?

The 1988 Chevy Cavalier spark plug wires are quite easy to remove. The spark plug wires simply pull off on each end. Put the new spark light wires on by pushing downward on each end.


How do you remove the ignition key cylinder in a 1988 Toyota pickup?

there is a small pin you can see through the plastic on the steering column in front of the ignition. you insert the key and push the pin to release the cylinder. you may need to remove wheel to get to it though.


What is the firing order for a 1988 Chevy Cavalier 4 cylinder?

Firing order 1-3-4-2 --- front | 1 | | 2 | of | 3 | vehicle | 4 | --- distributorless ignition


Does the z24 cavalier have a v6?

Yes, I have a 1988 and 1989 Chevy Cavalier Z24 and they both have the 2.8L V6


Clutch slave cylider location on a 1988 Pontiac Grand Am?

In a 1988 Pontiac Grand Am you will find the clutch slave cylinder located on the flywheel. You will need to remove the hush panel from the driver's side foot well to gain access to the clutch slave cylinder.


Where is the starter located on a 1988 Celebrity?

6 cylinder? Lower rear end of engine4 cylinder ? front of engine behind radiator lower section Disconnect the - battery cableRaise and support vehicleRemove wiring harness at top of starterRemove mounting boltsRemove starter