answersLogoWhite
Jeep Wrangler

How do you remove the windshield wiper motor on a 1992 Jeep Wrangler?

383940

Top Answer
User Avatar
Wiki User
2011-09-12 20:37:00
2011-09-12 20:37:00

you need to first put the windshield in the down position by removing the torx bolts on the side roll bars where they meet into the central roll bar. next, you need to remove the bottom torx bolt on the two sides just above the speakers to enable you to fold the windshield down. next, there are three torx screws holding the motor in and a connection under the dash for the electric. you need to pry the linkage off in the middle where the left wiper is and the nm the motor will come out. any more questions email me at bignanner@AOL.com

1

Related Questions

User Avatar

how to change the windshield wiper motor in a 2000 jeep wrangler

User Avatar

Remove the windshield wiper arm from the windshield wiper motor. Remove the wiring harness. Remove the retaining nut. Reverse the process to install the new windshield wiper motor.

User Avatar

# Remove the windshield wiper arms # Remove the cowl cover # Disconnect the electrical connector from the wiper motor # Detach the wiper motor/linkage assembly from the cowl # Remove the wiper motor retaining bolts and remove the motor

User Avatar

* Remove the windshield wiper arms * Remove the cowl cover * Disconnect the electrical connectorr from the wiper motor * Detach the wiper motor/linkage assembly from the cowl * Remove the wiper motor retaining bolts and remove the motor

User Avatar

The motor sits under the cowl at the base of the wiper arm.

User Avatar

# Remove the wiper arms # Remove the windshield wiper cowl cover # Disconnect the electrical connector from the wiper motor and remove the motor # Remove the wiper motor retaining bolts # Pry the linkage arm off the wiper motor pin with large screwdriver

User Avatar

Where is the wiper motor located on a 1989 jeep wrang ler

User Avatar

Remove the wiring harness from the wiper motor. Remove the windshield wiper arm from the wiper motor. Remove the wiper motor retaining screws. Reverse the process to install the new wiper motor.

User Avatar

You will have to remove the wiper arms, then remove the cowl, and then the wiper motor.

User Avatar

It is under the wiper cowl. The painted piece in front of the windshield.

User Avatar

The wiper motor is mounted on the left inside of the windshield frame on the same bracket as the VIN. Fold down the windshield and is fully accessible.

User Avatar

you have to remove the panle on the outside of the jeep between the hood and the windshield. 4 screws.

User Avatar

The 1988 Jeep windshield wiper motor is located on the firewall in the engine compartment. The wiper motor will be in the center of the firewall.

User Avatar

The wiper motor is on the driver's side, behind the dash board. if you fold you front windshield down, that will expose your wiper motor.

User Avatar

http://www.ehow.com/video_4936070_install-windshield-wiper-motor.html?pid=1&cp=1 (this is a complete video on how to remove and replace a wiper motor...very informative.)

User Avatar

You have to remove the linkage from the wiper motor.

User Avatar

Unbolt the roll bar from the windshield. Lower the windshield. At this point you can unbolt the motor and replace it.

User Avatar

http://www.ehow.com/video_4936070_install-windshield-wiper-motor.html?pid=1&cp=1 (this is very informative video on how to remove and replace a windshield wiper motor)

User Avatar

You begin to remove the windshield wiper motor by removing the cowl. Disconnect the wiper unit drain tubes and remove the mounting bolts. Replace with working unit

User Avatar

Mounted on the firewall directly behind the brake master cylinder reservoir. UNDER WINDSHIELD WIPER COWL COVER remove the wiper arms remove the windshield wiper cowl cover disconnect the eletrical connector from the wiper motor and remove the motor remove the wiper motor retsining bolts pry the linkage arm off the wiper motor pin with large screwdriver

User Avatar

* Remove the wiper arms * Remove the windshield wiper cowl cover * Disconnect the electrical connector from the wiper motor and remove the motor * Remove the wiper motor retaining bolts * Pry the linkage arm off the wiper motor pin with a large screwdriver

User Avatar

wiper motor arm has a small c-clip to remove and then same arm other end has a ball type that you pry off with a small cats paw type bar or screwdriver. this will remove the short wiper motor arm and then you can remove both wiper arms out thru slots in windshield frame. Be sure to remove plastic nuts on both wipers on front side of windshield frame.

User Avatar

* Pry off the cover for the wiper arm nuts unscrew the nuts and remove both wiper arms * disconnect the windshield washer line remove the single retaining screw release the five push-in retainers and remove the cowl cover * Unplug the electrical connector from the windshield wiper motor * Remove the three wiper motor assembly retaining bolts and remove the wiper motor assembly * Detach the wiper transmission assembly from the wiper motor crank arm * Detach the wiper motor crank arm from the wiper motor assembly * Remove the three wiper motor retaining screws and detach the wiper motor from bracket


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.